Bedienungsanleitung Olympia A 240 Combo (Seite 16 von 75) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

569117

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

6 Operation

6.1 Laminator

The laminator can complete hot and cold lamination:

Ɣ In the case of hot lamination, the lamination foil is adhered together.

Ɣ In the case of cold lamination, the lamination foil is pressed together.

Select the lamination method according to the material to be laminated.

Note: Only cold lamination should be used for thermopaper and

ultrasonic images!

6.1.1 Hot laminating

Use the function switch, a sliding switch, to select the lamination foil

thickness you want to process and the laminator automatically activates the

temperature level associated with the corresponding thickness:

Ɣ 60 or 80 mic

100 or 125 mic

1. Set the function switch, located at the top of the device on the right-hand

side, to the lamination foil thickness being used. The laminator heats up

to the required temperature automatically. The READY indicator flashes

orange during the warm-up phase.

2. The drive motor for the transport rollers starts up.

3. The correct operating temperature is reached after about 5 minutes and

the READY indicator lights up green.

4. Insert the document to be laminated in the lamination foil so that there is

a margin of approx. 3 - 5 mm to the edge of the foil on all sides.

Note: Only use hot lamination foil for hot laminating.

5. Guide the laminating foil containing the document to be laminated in the

laminator infeed with the closed side first. The laminating process occurs

automatically.

Note: To prevent the lamination foil from creasing, never feed the

open side of the lamination foil first in the laminator infeed. When

inserting the lamination foil, observe the instructions on the infeed slot.

mic or micron = abbreviation of the word micrometer (m). 1 micrometer is one thousandth

of a millimetre. Examples: 60 m = 0.06 mm. 80 m = 0.08 mm. 100 m = 0.1 mm. 125 m

= 0.125 mm.

1 Connect the power cable to an easily accessible, standard electrical

socket.

Caution: Check that the voltage specifications of the unit correspond

to that of your power supply network (220 - 240 V, 50 Hz).

2 Use the on/off switch on the right of the appliance to switch on:

"+27", the red display lamp shows.

3 The drive motor for the transport rollers starts up. The correct operating

temperature is reached after about 3-5 minutes and the green display

lamp shows.

4 Insert the document to be laminated in the pouches so that there is a

margin of approx. 3 - 5 mm to the edge of the foil on all sides.

Caution: Only use foil intended for hot laminating.

5 Insert the foil containing the document in the laminator's insertion slot.

Insert the ready closed side of the pouch first.

Note: To prevent the laminating foil from creasing, never insert the

open end of the foil pocket in the insertion slot of the laminator first. When

inserting the foil, observe the instructions on the insertion slot. The laminat-

ing process occurs automatically.

Caution: The lamination foil is very hot and soft when ejected

following lamination. Therefore, handle the laminated document with

due care!

Note: To flatten and smoothen the laminated product, place a book or

similar heavy, flat object on it.

6. When you have completed the laminating process, set the function

switch, located at the top of the device on the right-hand side, to COLD

and remove the power plug from the power socket. Let the device cool

down before packing it away, for example.

Caution: The device is very hot directly after laminating! Risk of

injury!

6.1.2 Cold laminating

Attention: If you have just finished using the laminator for hot

laminating, you must let the laminator cool down. It takes about 30

minutes to cool down sufficiently.

1. Set the function switch, located at the top of the device on the right-hand

side, to COLD.

Note: Only use cold lamination foil for cold laminating.

2. Remove the protective foil from the lamination foil.

3. Insert the document to be laminated in the lamination foil so that there is

a margin of approx. 3 - 5 mm to the edge of the foil on all sides.

4. Guide the laminating foil containing the document to be laminated in the

laminator infeed with the closed side first. The laminating process occurs

automatically.

Note: To prevent the lamination foil from creasing, never feed the

open side of the lamination foil first in the laminator infeed. When

inserting the lamination foil, observe the instructions on the infeed slot.

:KHQ\RXKDYHFRPSOHWHGWKHODPLQDWLQJWXUQWKHIXQFWLRQVZLWFKWRWKH

ULJKWLQWKHCOLDSRVLWLRQDQGUHPRYHWKHPDLQVSOXJIURPWKHZDOOVRFNHW

/HWWKHGHYLFHFRROGRZQEHIRUHSDFNLQJLWDZD\IRUH[DPSOH

7XUQWKHIXQFWLRQVZLWFKWRWKHULJKWLQWKHCOLDSRVLWLRQ



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympia A 240 Combo Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info