Bedienungsanleitung Olympia PS 17 CD (Seite 7 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

569264

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Clearing a jam

If too much paper is inserted in the cutting unit, it will cause a jam.

Proceed as follows:

- Push the sliding switch to the Paper Rev /CD position.

- The cutting unit runs backwards and pushes the excess paper back.

- Reduce the quantity and slide the switch to Paper Auto / CD again. The cutting unit runs

forward again and the residue remaining is shredded.

If the backwards and forwards movement does not remedy the jam, pull out the mains plug

and remove the remaining manually from the cutting unit.

Motor protection

The motor switches off automatically in the event of overloading. Pull out the mains plug

from the socket and allow the motor to cool down to room temperature. Plug the mains

cable back in and then continue operation.

Notes on care and maintenance

Caution: maintenance work may only be performed when the mains plug is pulled out.

To ensure your shredder enjoys a long working life, we recommend to clear residual material

from the cutting units at regular intervals and apply

special oil for paper shredders to the

cutting unit. This special oil is available from specialist dealers or directly from our service centre

in Hattingen. This will extend the service life of the device.

Technical data

Model: PS 17 CD

Power supply: 220-240 V / 50Hz

Cutting width of the paper slot: 215 mm, width of cut strips: 7 mm

Cutting width of the CD slot: 120 mm, width of cut strips: approx. 30 mm

Cutting power: 7 DIN A4 sheets (70 g/m

), 1 CD

Security level: 1

Max. power consumption: 0.5 A

Size (W x H x D): 300 x 185 x 320 mm

Weight: 3.6 kg

Operating cycle paper: 2 min. on, 15 min. off

Operating cycle CD: 2 min. on, 15 min. off

Device malfunctions

Problem Cause Remedy

Is the mains cable plugged

properly in the socket?

Plug the mains cable into the socket

properly.

Is the sliding switch set to

Off?

Set the sliding switch to Paper Auto

or Paper Rev / CD.

Device does not

work

Does the motor not start when

paper is inserted?

Slide the paper in the respective slot

so that it touches the sensor in the

centre.

Device does not

work after lengthy

operation or stops

during operation

Was the device in constant

operation for some time?

Is the surface of the device

warm?

Pull out the mains plug from the

socket and allow the motor to cool

down to room temperature.

Jam Have you inserted more than

7 sheets of paper (70 g/m²) or

more than 1 CD?

Has the material not been

inserted straight in the in-feed

slot?

Set the sliding switch to

Paper Rev / CD to push back the

paper. Switch the device to Paper

Auto again to shred the paper

remaining in the cutting unit.

If you cannot rectify the fault yourself, contact your dealer or call the Olympia hotline.

Disposal Notes

This symbol [the crossed-out wheeled bin/PICTURE] means that the product should be

brought to the return and or separate collection systems available to end-users, when the

product has reached the end of its lifetime. This symbol applies only to the countries within

the EEA (*).

(*) EEA = European Economic Area, which comprises the EU Member States

plus Norway, Iceland, and Liechtenstein.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympia PS 17 CD Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info