Bedienungsanleitung Olympus DS150 (Seite 8 von 18) (Englisch)

18427

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

1514

Follow the procedure below to set the user ID number:

ERASE SP DICT

INDEX/

FOLDER

ERASE SP DICT

INDEX/

FOLDER

ᕃ

ᕄ

ᕅ ᕆ

ᕃ

In the Stop mode, press and hold the MENU switch

for at least 2 seconds. The menu will be dis-

played on the LCD panel

ᕣ

ᕄ

twice the MENU switch's up/down control in the down direction to display [ID AAA] (when in the ini-

tial setting). The cursor will start blinking at the first digit's position.

ᕅ

Turn the MENU switch's up/down control in the up direction to change the character displayed: [A]

Ǟ [B] Ǟ [C]

……

[X] Ǟ [Y] Ǟ [Z] Ǟ [0] Ǟ [1] Ǟ [2] Ǟ

……

[7] Ǟ [8] Ǟ [9] Ǟ [A] Ǟ [B]

……

ᕆ

When the desired character is displayed, press the MENU switch to set it. The blinking cursor

moves to the next position.

ᕇ

Follow the same procedure to set each character. When ID setting is complete, press the MENU

switch to enter the Format mode. (See page 31.)

ᕈ

Pressing the STOP button instead of the MENU switch after ID setting ends menu setting and

restores the Stop mode.

If the Format mode is entered in

ᕇ

but you do not need to format the built-in memory, press the

STOP button. This ends menu setting and restores the Stop mode.

ᕃ

Make sure [NEW], memory remaining time, and the message number are displayed on the LCD

panel. Ensure there is sufficient remaining time available for your message and select the folder

([A] or [B]), microphone sensitivity ([DICT] or [CONF]) and recording mode ([SP] and [LP]).

ᕄ

To change the folder, press the INDEX/FOLDER button

ᕢ

to move to the position after the last

recording in the other folder. To change the microphone sensitivity or recording mode, use the

menu (see page 29 for the change procedure).

ᕅ

Press the REC button

ᕡ

to start recording. The LED

ᕥ

lights and recording starts.

ᕆ

Press the STOP button to stop recording and enter the Stop mode.

ᕇ

You can monitor what is being recorded through an earphone plugged into the EAR jack

ᕧ

(recording monitor).

If [NEW] is not displayed when you press the REC button, insertion recording will start. This over-

writes the previous recording so be sure you always check the display before pressing the REC

button.

If [FULL] is displayed on the LCD panel, additional recording is not possible. In this case, erase

unnecessary messages to free up more memory. If there are any messages that you want to pre-

serve, transfer the voice data to a PC using the PC transfer kit (available as a standard or optional

accessory).

Do not connect or disconnect the AC adapter plug during recording. Always enter the Stop mode

before plugging or unplugging the adapter. Otherwise, you will not be able to play back the mes-

sage being recorded.

The recording monitor volume cannot be adjusted.

Always use the SP mode if you want to record high-quality voice data suitable for transfer to a PC

for use in voice recognition operations.

(For more about voice recognition, see page 33.)

BASIC OPERATION

RECORDING

ᕃ

REC STOP

INDEX/

FOLDER

ᕄ ᕅ ᕆ

Remaining

memory time

Message No.

T572 Inst DS-150-E.Q33J 1999/4/26 0:57 PM y[W 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympus DS150 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info