Bedienungsanleitung Olympus E-30 (Seite 81 von 156) (Englisch)

62315

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Flash shooting

You cannot use the camera to adjust the amount of light emitted from a commercially

available flash except for a flash specified for use with this camera. To use a commercially

available flash, connect it to the hot shoe or connect the synchronization cord to the external

flash connector. Set the camera’s shooting mode to M. For details on non-specified

commercial flashes, see “Non-specified commercial flashes” (gP. 81).

1Remove the hot shoe cover to connect the flash

unit to the camera.

2Set the shooting mode to M, then set the aperture

value and shutter speed.

• Set the shutter speed to 1/250 sec. or slower. If the

shutter speed is faster than this, commercially available

flashes cannot be used.

• A slower shutter speed may produce blurred images.

3Turn on the flash.

• Be sure to turn on the flash after attaching the flash unit

to the camera.

4Set the ISO sensitivity and aperture value on the

camera to match the flash control mode on the

flash.

• Refer to the flash’s manual for instructions on how to set

its flash control mode.

xNotes

• The flash fires each time the shutter is released. When you do not need to use the flash, turn

off the flash’s power.

• Check beforehand that the flash you are using is synchronized with the camera.

Non-specified commercial flashes

1) Some commercially available flashes require a voltage of 250V or more for the

synchronization connector. The use of this type of flash can damage the camera or

prevent the camera from operating properly. Contact the manufacturer of the flash for the

specifications of the flash synchronization connector.

2) Some commercially available flashes have a synchronization connector with reversed

polarity. This type of flash does not work with this camera. Contact the manufacturer of the

flash.

3) Exposures when using a flash require that adjustments be made on the flash. If a flash is

used in the auto mode, match it with the f-number and ISO sensitivity settings on the

camera.

4) Even if the flash auto f-number and ISO sensitivity are set the same as on the camera, the

correct exposure may not be obtained depending on the shooting conditions. In such a

case, adjust the auto f-number or ISO on the flash or calculate the distance in the manual

mode.

5) Use a flash with an illumination angle that matches the focal length of the lens. The focal

length of the lens for 35 mm film is approximately twice as long as the focal length of the

lenses designed for this camera.

6) Do not use a flash unit or other accessory TTL flash that has additional communication

functions other than the specified flashes, since it may not only fail to function normally,

but may also cause damage to the camera’s circuitry.

Using commercially available flashes

Hot shoe cover

External flash connector

s0017_e_00_0_unified.book Page 81 Thursday, October 30, 2008 2:47 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympus E-30 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Olympus E-30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info