Bedienungsanleitung Olympus FC-1 Macro Flash System (Seite 14 von 53) (Englisch)

589209

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

14 15

Confirm that both the camera and Macro Flash Controller are off.

Attaching or removing the Macro Flash Controller while either it or the camera is on may result in

malfunction.

How to attach

1. Place the head section in the standard position (horizon-

tal, front).

2. Remove the hot shoe cover from the camera.

• Store the hot shoe cover in the pocket of the macro flash

case to avoid losing it.

3. Loosen the lock ring.

• If the lock pin is in the out position, put it to the in position by

turning it all the way in the opposite direction to [←LOCK]

until it stops.

• Do not apply excessive force to the lock pin.

• Do not touch the electric contact with a finger or metallic object.

• Do not attach the Macro Flash Controller while the lock pin is in the out

position. Otherwise, malfunction may result.

4. Slide the Macro Flash Controller all the way into the hot

shoe until it clicks and stops.

5. Tu rn the lock ring all the way in the direction of [←LOCK]

until it stops.

How to remove

1. Loosen the lock ring, then slide the Macro Flash Control-

ler out of the hot shoe.

2. Attach the hot shoe cover to the camera.

Lock pin

Electric contact

Attach the RF-11 Ring Flash or TF-22 Twin Flash to the Macro Flash Controller.

• How to use the RF-11 Ring Flash : See page 15.

• How to use the TF-22 Twin Flash : See page 27.

RING FLASH RF-11

1. While aligning the indices, attach the RF-11 Ring Flash to

the lens.

2. Press the Ring Flash release button of the FC-1 Macro

Flash Controller to remove the cap.

3. IInsert the RF-11 Ring Flash connector terminal into the

Ring Flash connector on the FC-1 Macro Flash Controller

until it clicks.

• When unplugging the connector, be sure to press and hold

the Ring Flash release button. Be sure to attach the cap

after unplugging the connector.

• Do not pull the cord when plugging or unplugging the con-

nector. Always grasp it by the connector plug. Pulling the

cord could damage the connector wire.

• Attach the FC-1 Macro Flash Controller to the camera beforehand.

• To prevent the Ring Flash from falling off, attach it with the camera in a stable position.

Notes

• Confirm that both the Macro Flash Controller and Ring Flash are off before attaching or removing them. Otherwise,

malfunction may result.

• Be sure to leave the Twin Flash connectors capped. Otherwise, the Macro Flash Controller cannot be turned on.

Memo

The Ring Flash and Twin Flash connector terminals are subject to high voltages. To ensure safety, the Macro Flash

Controller is designed so that it cannot be turned on unless one of the flashes is connected to it and all of its unused

connectors are capped.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olympus FC-1 Macro Flash System Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info