Bedienungsanleitung Omega OSD20 (Seite 5 von 12) (Englisch)

651592

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Instructions for Machine Transport

NOTE: Refrigerated equipment must remain upright to avoid damage to the compressor.

In order to prevent the oil contained in the compressor from flowing into the cooling system, it is

necessary to always ship, carry, store and handle this drink dispenser in an upright position, fol-

lowing the instructions located on the packaging. Never ship, carry, store or handle this unit on

its side.

1.1 RECEIVING

Each unit is completely tested under operating conditions and thoroughly inspected before

shipment. At the time of shipment, the carrier is responsible for the unit and any claim for dam-

age must be made with the carrier. Upon receiving units from the delivering carrier, carefully in-

spect the carton for visible indication(s) of damage. If damage exists, have carrier note same

on bill of lading and file a claim with the carrier.

1.2 UNPACKING

A. Cut band and remove.

B. Carefully remove top portion of carton by lifting up, see figure 1.

C. Remove top inner carton pad from inside of packing box.

D. Inspect unit for concealed damage and if evident, notify delivering carrier and file

a claim against same.

Installation Positioning the machine

The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides and back of

the machine to allow proper ventilation. Installation of the machine near a heat source

should be avoided. Some heat sources you should avoid locating this unit too close to are

ovens, coffee machines, cold or frozen beverage dispensers or ice machines (equipment with

compressors that expel hot air through its vents). A room temperature between 59°F (15°C)

and 77°F (25°C) is recommended.

Connection to Main Power Supply

• The electrical safety of this drink dispenser can only be achieved if the machine is properly

connected to an appropriate grounded receptacle that is in compliance with current national

safety standards. Therefore, the manufacturer cannot be held responsible for damage and/or

injury caused by failure to connect the unit to an appropriate source of power.

• For a safe and correct installation, connect the unit to a dedicated outlet.

• Do not alter the cord or plug in any way.

• The entire length of the power supply cord must not, in any way, be compressed, bent, or

bunched together, nor may extension cords be used.

• Do not obstruct the ventilation vents on the side and rear panels of the unit. Insufficient venti-

lation will reduce the efficiency of the machine, causing it to function inadequately, and can

cause serious damage. A minimum of eight inches (20cm) clearance is necessary on each side

and behind the unit.

WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE FATAL

ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR. THE POWER CORD IS PROVIDED WITH

A THREE PRONG GROUNDED PLUG. IF A THREE-HOLE GROUNDED ELECTRICAL OUTLET IS NOT

AVAILABLE, USE AN APPROVED METHOD TO GROUND THE UNIT. DO NOT USE EXTENSION CORDS

WITH THIS UNIT. DO NOT “GANG” TOGETHER WITH OTHER ELECTRICAL DEVICES ON THE

SAME OUTLET.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Omega OSD20 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info