Bedienungsanleitung One for All URC 3050 So Easy 3 (Seite 2 von 4) (Englisch)

492772

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Step 1:

Installing the Batteries

Step 3:

Setting Up Your Devices

Match the batteries to the + and - marks inside

the battery case, then insert the batteries.

Press the battery cover back into place.

1st TV code

2nd TV code

3rd TV code

1st VCR code

2nd VCR code

3rd VCR code

1st Cable code

2nd Cable code

3rd Cable Code

Step 2:

Looking Up Your Electronic Device Code

You will need one of these codes to program your One For All

Easy 3 Device remote.

Look at your Electronic Device to find out the brand name and

write it in the space below:

TV ________________________

VCR _______________________

Cable _______________________

Your One For All

So Easy 3 Device needs two (2) new AAA

alkaline batteries. To install the batteries:

On the back of the

One For All

So Easy 3

Device, push down on the tab and lift the

cover off.

Set-Up Codes

RCA 1213

Sony 1111

Turn on your TV, VCR or Cable Box, depending on the

device you are programming.

Press TV* and release. Press and hold SETUP

until the One For All

So Easy 3 Device's red

light blinks twice. Release SETUP.

* Note: When setting up your VCR and/or Cable Box,

substitute the appropriate device key (VCR or CBL).

Using the example

shown on the

right, enter the

first four-digit

code you wrote

down for the

device you are

setting up. (See

"Looking Up Your

Electronic Device

Code".) If you put

in the code

correctly, the red

light will blink

twice.

Test the unit by pressing POWER. The red

light (LED) should blink once.

Note: Removing the batteries for more than 30 minutes will require you to

reprogram the remote control.

Find your Device brand in the listing on the

reverse side of these instructions. The most

popular codes are listed first. Write your codes

here:

How to Enter Codes

If your TV Press

code is:

TV Set Up

Aim the One For All

So Easy3 Device at your

TV and press POWER. Your TV should turn off.

If it doesn't, repeat Steps 2-4, trying each code listed

for your brand until you find the one that operates

your TV.

VCR Set Up

Aim the One For All

So Easy3 Device at your

VCR and press POWER. Your VCR should turn

off. If it doesn't, repeat Steps 2-4, trying each code

listed for your brand until you find the one that

operates your VCR. If your original VCR remote

did not have a POWER key, put a tape in your

VCR and press PLAY on the One For All

Easy3 Device.

Cable Set Up

Aim the One For All

So Easy 3 Device at your

Cable Box and press POWER. Your Cable Box

should turn off. If it doesn't, repeat Steps 2-4, trying

each code listed for your brand until you find the

one that operates your Cable Box. If your original

Cable Box remote did not have a "ON" key, Use

CH + on the One For All

So Easy 3 Device to

turn your Cable Box on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

One for All URC 3050 So Easy 3 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info