Bedienungsanleitung OneQ Flame (Seite 10 von 21) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Schwedisch, Finnisch)

798832

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

-10-

oneQ B.V. 2022

one-q.com

BURNER ASSEMBLY

The burner hangs loose in the slot of the stand. Choose an accessible place for you to install the controls in the preparation of the

barbecue.

Ü figure A Place the drip tray in the appropriate/suitable hole of the plateau.

Ü figure B Carefuly release the (gas)burner in the slot of the stand. Place the points of the 2 flame distributors into

the holes of the burner.

Ü figure C Put the grill (or the optional Teppan Yaki plate) over the edge of the burner. Then place the control knob

on the gas tap and insert the battery.

CONNECTION GAS BOTTLE

The oneQ gasbarbecue is suitable for both propane and propane / butane (gas). We advise you to use standard 5 or 10 kg cylinders.

Use a regulator that matches the pressure indicated on the date plate (EN16129).

Ü figure D/E Bend the four notches on the cross up. Place the cylinder on the cross, with the bottom of the bottle

around the ridges. Then attach the hose to the gas tap by turning/ tighten the nut.

OPERATION AND FIRST USE

The (gas) burner is fully assembled and properly adjusted at the delivery by the manufacturer. In the first use of the barbecue it is

important that you completely remove all packaging materials.

Before you use the grid or plate for the first time, you should wash it in hot water with mild detergent, rinse and dry it. After that, put it

on the (gas)burner.

Ü figure F Press the control knob and turn it to the left to the ignition position until the burners are burning

completely.

Depending on the type of gas and gas pressure the oneQ barbecue has a load of 6,7-8,0 kW. The burnerpower can be adjusted with the

knob. Do not fully heat up the barbecue when using a Plate and/or Top or Hood (keep the knob in the downward position at all times).

Ü figure G The grill and Teppan Yaki plate have a high-and low-temperature zone. This distribution offers a

convenient range while preparing food.

TROUBLESHOOTING

Failures Possible Cause Solution

Burner will not ignite - ignitionpin dirty clean pin

or does not burn - cylinder (almost) empty replace cylinder

completely. - hose kinked remove kink

- restriction air intake manifold release air intake

- burner tubes are wet (after cleaning) leave to dry

- Defective pressure regulator replace

Ü figure H The 2 air intakes at the bottom of the manifold should have an unobstructed air input. If there is dirt in it

should remove it.

Is the problem remains unresolved then contact your oneQ supplier.

CLEANING & MAINTENANCE

We recommend cleaning the grills, Teppan Yaki plate (optional), baffle and burner after each use. Check all areas where oil, grease or

food residue may accumulate, then you keep all parts in optimal condition.

SERVICE, WARRANTY AND CERTIFICATIONS

If you have problems with your oneQ flame or if you want to order (reserve) parts, contact your dealer or see www.one-q.com, where

you find an extensive customer service section.

the oneQ barbecue measures up to the NEN-EN 498 standard for barbecues and is certified by the world-renowned KIWA GASTEC

testing station for gas appliances.

ONEQ B.V.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

OneQ Flame Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info