Bedienungsanleitung Onkyo A-9010B-S (Seite 12 von 16) (Englisch)

581067

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Operations

En-12

Adjusting sound quality, etc.

∫ DIRECT

Audio is output through shortest path which is

advantageous to sound quality without passing the sound

quality adjustment circuit (BASS, TREBLE).

1. Press the DIRECT button.

DIRECT function is enabled and the DIRECT LED

lights up.

0 BASS, TREBLE, and LOUDNESS is disabled when

the DIRECT function is enabled.

To cancel the DIRECT function: Press the DIRECT

button again to cancel, and the DIRECT LED goes off.

∫ LOUDNESS

Bass and treble is enhanced when the volume is turned

down.

1. Press the LOUDNESS button.

LOUDNESS function is enabled and the

LOUDNESS LED lights up.

0 When the DIRECT function is enabled, LOUDNESS

function will not be enabled even when the

LOUDNESS button is pressed. Press the

LOUDNESS button after canceling the DIRECT

function by pressing the DIRECT button.

0 When the BASS or TREBLE is raised very high,

effect of the LOUDNESS will become smaller.

To cancel the LOUDNESS function: Press the

LOUDNESS button again to cancel, and the LOUDNESS

LED goes off. Also, the LOUDNESS function will be

canceled when the DIRECT function is enabled.

∫ BASS

Adjusts the bass.

1. Turn the BASS control.

0 BASS is disabled when the DIRECT function is

enabled.

0 When the LOUDNESS function is enabled,

adjustment range in i direction for BASS will

become smaller.

∫ TREBLE

Adjusts the treble.

1. Turn the TREBLE control.

0 TREBLE is disabled when the DIRECT function is

enabled.

0 When the LOUDNESS function is enabled,

adjustment range in i direction for TREBLE will

become smaller.

∫ BALANCE

Adjusts the audio output balance between the left and

right speakers.

1. Turn the BALANCE control.

Using headphones

Turn down the volume, then connect your stereo

headphones with a standard plug (ø 6.3 mm, 1/4q) to the

PHONES jack. The speakers output no sound while

the headphones are connected.

Setting the Auto Standby function

This unit will go into standby mode automatically with

following conditions when the Auto Standby is set to On.

0 When there is no audio in the currently selected input

source and this unit is not operated for approximately

20 minutes

0 (North American and Continental European models)

When there is no PCM signal input in D 1 or D 2, and

this unit is not operated for approximately 20 minutes

The default Auto Standby setting is set as follows.

(North American models) Off

(Others) On

The setting can be changed with following procedure.

1. Press and hold the Í ON/STANDBY button while

the power is in standby. The power will come on when

the button is pressed, but keep on pressing the button.

The setting for the Auto Standby is changed, and it will

be displayed as follows.

(North American and Continental European models)

On: D 1 LED will blink for approximately 2 seconds.

Off: D 2 LED will blink for approximately 2 seconds.

(UK models)

On: ASB LED will light up.

Off: ASB LED will go off.

A-9010_eng.book 12 ページ２０１４年１２月２５日　木曜日　午前１０時４８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo A-9010B-S Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo A-9010B-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info