Bedienungsanleitung Onkyo A-9030 (Seite 27 von 32) (Englisch)

492685

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

There’s no sound.

• Make sure that the Onkyo Dock is connected to the

integrated amplifier properly.

• Make sure that no video content is being played.

• Reset the iPod.

Other

• When the Auto Standby (ASb) function is activated, the

power of the Onkyo Dock connected via u is

automatically turned off (➔ page 25).

Can’t control properly by using the remote

controller.

• Make sure that the u cable is connected to the

integrated amplifier correctly.

Check that each device is connected correctly and that

the RI MODE switch is set correctly (➔ page 17).

No sound is heard from a connected

component.

• Make sure the correct input source is selected

(➔ page 23).

• Make sure the analog audio cable is connected correctly

(➔ page 14).

When the u interlock does not function

properly

• Check that each device is connected correctly and that

the RI MODE switch is set correctly

(➔ pages 15

to 17).

• Check that the switch on the back of the integrated

amplifier is set to the correct setting.

• The settings are not enabled when the switch is changed

during the Standby mode.

To change a setting, be sure to turn on the unit prior to

making any changes.

• The connecting method may vary depending on the

device that will be connected. Please refer to the u

connection section in the owner’s manual of the

connected device.

The sound from turntable is distorted.

• If your turntable has a built-in phono preamp, connect to

other analog inputs such as LINE IN.

• If your turntable does not have a built-in phono preamp,

connect a turntable to PHONO (➔ page 19).

• Make sure that the ground wire is connected. Otherwise,

it may produce an audible hum and noise.

The remote controller doesn’t work

properly.

• Make sure the batteries have been installed with the

correct polarity (+/–) (➔ page 7).

• Replace both batteries with new ones. (Do not mix

different types of batteries or new and old batteries.)

• The remote controller is too far away from the integrated

amplifier, or there’s an obstacle between them

(➔ page 7).

• The integrated amplifier’s remote control sensor is being

subjected to bright light (inverter-type fluorescent light

or sunlight).

• The integrated amplifier is located behind the glass

doors of an audio rack or cabinet.

Onkyo Dock

External Components

Remote Controller

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded

correctly.

The integrated amplifier contains a microcomputer

for signal processing and control functions. In very

rare situations, severe interference, noise from an

external source, or static electricity may cause it to

lockup. In the unlikely event that this should happen,

unplug the power cord, wait at least 5 seconds, and

then plug it again.

Before disconnecting the power cord from the wall

outlet, set the integrated amplifier to Standby.

If during idling the cover is too hot to touch, then

ventilation needs to be improved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo A-9030 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo A-9030

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info