Bedienungsanleitung Onkyo cr 305 tx (Seite 3 von 36) (Englisch)

158316

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

21. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the origi-

nal part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to

the appliance, ask the service technician to perform safety checks

to determine that the appliance is in proper operation condition.

23. Wall or Ceiling Mounting – The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (in-

cluding amplifiers) that produce heat.

25. Liquid Hazards – The appliance shall not be exposed to drip-

ping or splashing and no objects filled with liquids, such as vases

shall be placed on the appliance.

1. Recording Copyright

Recording of copyrighted material for other than personal use is il-

legal without permission of the copyright holder.

2. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If

power does not come on, contact your Onkyo authorized service

station.

3. Care

From time to time you should wipe the front and rear panels and the

cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a

weak solution of mild detergent and water, wring it out dry, and

wipe off the dirt. Following this, dry immediately with a clean cloth.

Do not use rough material, thinners, alcohol or other chemical sol-

vents or cloths since these could damage the finish or remove the

panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to coun-

try or region. Be sure that the power supply voltage of the area where

this unit will be used meets the required voltage (e.g., AC 120 V, 60

Hz) written on the rear panel.

Setting the STANDBY/ON button to standby does not shut off the

power completely. So the power cord should be removed from the

AC outlet when the unit is not used for a prolonged time.

5. Do not touch this unit with wet hands

Do not handle this unit or power cord when your hands are wet or

damp. If water or any other liquid enters the case, take this unit to an

authorized service center for inspection.

6. Location of this unit

Place this unit in a well-ventilated location.

Take special care to provide plenty of ventilation on all sides of this

unit especially when it is placed in an audio rack. If ventilation is

blocked, this unit may overheat and malfunction.

Do not expose this unit to direct sunlight or heating units as this

unit's internal temperature may rise and shorten the life of the pickup.

Avoid damp and dusty places and places directly affected by vibra-

tions from the speakers. In particular, avoid placing the unit on or

above one of the speakers.

Be sure this unit is placed in a horizontal position. Never place it on

its side or on a slanted surface as it may malfunction.

Do not place near tuners or TV sets.

If placed next to a TV or tuner, it may cause reception interference

resulting in some noise in the TV or tuner output.

7. Points to remember

If this unit is brought from a cold environment to a warm one or is in

a cold room that is quickly heated, condensation may form on the

pickup, preventing proper operation. In this case, remove the disc and

leave the power ON for about one hour to remove the condensation.

When transporting this unit, be careful not to bump it.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELEC-

TRICAL CODE, ANSI/NFPA 70

Precautions

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

S2898A

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

INDUSTRIESTRASSE 20

82110 GERMERING,

GERMANY

GERMERING, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

I. MORI

declare in own responsibility, that the ONKYO product described

in this instruction manual is in compliance with the corresponding

technical standards such as EN60065, EN55013, EN55020 and

EN61000-3-2, -3-3.

This unit contains a semiconductor laser system and is classified as

a “CLASS 1 LASER PRODUCT.” So, to use this model properly,

read this Instruction Manual carefully. In case of any trouble, please

contact the store where you purchased the unit. To prevent being

exposed to the laser beam, do not try to open the enclosure.

DANGER:

INVISIBLE LASER RADIATION WHEN OPEN AND INTER-

LOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION:

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR

ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

For European model

This label on the right side of the panel states that:

1. This unit is a CLASS 1 LASER PRODUCT and employs a laser

inside the cabinet.

2. To prevent the laser from being exposed, do not remove the cover.

Refer servicing to qualified personnel.

“CLASS 1 LASER

PRODUCT”

Onkyo cr 305 tx Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info