67771
12
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
En
CD Receiver
CR-515DAB
CR-315DAB
Instruction Manual
Thank you for purchasing an Onkyo CD Receiver.
Please read this manual thoroughly before making
any connections and plugging it in.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new CD Receiver.
Please retain this manual for future reference.
Contents
Getting Started .......................... 2
Connections ............................ 16
Basic Operation ...................... 27
Playing a Disc.......................... 30
Listening to the Radio ........... 38
Clock and Timer ...................... 49
Miscellaneous ......................... 56
Troubleshooting................................ 56
If you can’t resolve an issue, try reset-
ting the CD receiver by holding down
the [ ] button and pressing the
[STANDBY/ON] button.
2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia-
tors, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table spec-
ified by the manufacturer, or
sold with the apparatus.
When a cart is used, use cau-
tion when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is dam-
aged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous volt-
age points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and fol-
low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is ade-
quate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
PORTABLE CART WARNING
S3125A
3
Precautions
1. Recording Copyright
—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
2. AC Fuse
—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care
Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners, alco-
hol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
Pressing the [STANDBY/ON] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands
—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
6. Handling Notes
If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
This unit’s top and rear panels may get warm
after prolonged use. This is normal.
If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
When you’ve finished using this unit, remove all
discs and turn off the power.
7. Installing this Unit
Install this unit in a well-ventilated location.
Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
•Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
8. To Obtain a Clear Picture
—This unit is a high-
tech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
your Onkyo dealer for details.
9. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
Moisture condensation can occur in the following
situations:
The unit is moved from a cold place to a warm
place.
–A heater is turned on, or cold air from an air
conditioner is hitting the unit.
In the summer, when this unit is moved from
an air conditioned room to a hot and humid
place.
The unit is used in a humid place.
Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
If condensation does occur, remove all discs and
leave this unit turned on for two to three hours. By
this time, the unit will have warmed up and any con-
densation will have evaporated.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
K. MIYAGI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
4
Precautions
—Continued
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
DANGER:
VISIBLE AND/OR INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK FAILED OR
DEFEATED. DO NOT STARE INTO BEAM.
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CON-
TROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECI-
FIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
The label on the right is
applied on the rear panel.
1. This unit is a CLASS 1
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this appa-
ratus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as fol-
lows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for the
ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
Supplied Accessories
Make sure you have the following accessories:
* In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
Remote controller and two batteries (AA/R6)
Indoor FM antenna
(Connector type varies from country to country.)
AM loop antenna
DAB antenna
Power cord
(Plug type varies from country to country.)
5
Before Using the CD Receiver
Notes:
If the remote controller doesn’t work reliably, try
replacing the batteries.
Don’t mix new and old batteries or different types of
batteries.
If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
When you operate the remote controller, point it at the
CD receiver’s remote control sensor, as shown below.
Notes:
The remote controller may not work reliably if the CD
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
If another remote controller of the same type is used
in the same room, or the CD receiver is installed close
to equipment that uses infrared rays, the remote con-
troller may not work reliably.
Don’t put anything, such as a book, on the remote con-
troller because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
The remote controller may not work reliably if the CD
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
The remote controller will not work if there’s an
obstacle between it and the CD receiver’s remote con-
trol sensor.
Installing the Batteries
1
Detach the battery cover by pressing the
tab and pulling up the cover.
2
Insert two AA-size batteries into the bat-
tery compartment.
Carefully follow the polarity diagram (positive
(+) and negative (–) symbols) inside the battery
compartment.
3
After the batteries are installed and
seated correctly, attach the compartment
cover.
Using the Remote Controller
Appro
x. 5 m
(16 ft.)
Remote control sensor
CD receiver
6
Features
Amplifier
WRAT (Wide Range Amplifier Technology)
High Current, Low Impedance Drive
Discrete Output Stage Circuitry
Optimum Gain Volume Circuitry
Subwoofer Pre Out
— CR-515DAB —
VLSC (Vector Linear Shaping Circuitry)*
•4 Audio Inputs and 2 Outputs (1 on front panel)
— CR-315DAB —
•3 Audio Inputs (1 on front panel) and 1 Output
CD Player
Plays CDs, MP3 CDs, CD-Rs and CD-RWs
25 Track Programming
•2 Repeat Mode (Track/Full)
•4 Play Modes (Normal/Random/Memory/1 Folder)
— CR-515DAB —
•Wolfson Single-Bit D/A Converter
— CR-315DAB —
Single-Bit D/A Converter
Tuner & Other
•DAB Digital Radio
4-Program Timer (Play or Rec / Once or Every)
Sleep Timer
Battery-Free Memory Backup
Headphone Jack
Aluminium Front Panel
RI-Dock Compatible Remote Control (iPod Control
Capable)
* VLSC and the VLSC logo are registered trademarks of Onkyo
Corporation.
7
Contents
Basic Operations
Getting Started
Important Safety Instructions .............................. 2
Precautions ........................................................ 3
Supplied Accessories .........................................4
Before Using the CD Receiver ........................... 5
Installing the Batteries .................................... 5
Using the Remote Controller .......................... 5
Features ............................................................. 6
Contents ............................................................. 7
Getting to Know the CD Receiver ...................... 8
Front Panel ..................................................... 8
Display ......................................................... 10
Rear Panel ................................................... 11
Remote Controller ........................................ 12
Disc Notes ........................................................14
Connections
Connecting Antennas ....................................... 16
Connecting Speakers .......................................18
Connecting the Power Cord ......................... 25
First Time Setup (European Model Only) ........26
Setting the Clock with the AccuClock Function
(European Model Only) .............................26
Basic Operation
Basic Operation ...............................................27
Turning On the CD Receiver ........................ 27
Adjusting the Volume ................................... 27
Selecting the Input Source ........................... 27
Using Headphones ....................................... 27
Adjusting the Bass and Treble ..................... 28
Using the Super Bass Function .................... 28
Using the Direct Function ............................. 28
Muting the Sound ......................................... 28
Changing the Input Display .......................... 29
Playing a Disc
Playing CDs ..................................................... 30
Using the Remote Controller ........................ 31
Displaying CD Information ...........................31
Selecting/Playing MP3 Files ......................... 32
Displaying MP3 Information ......................... 34
Listening to the Radio
Listening to the Radio ....................................... 38
Tuning into FM/AM Radio Stations ...............38
Displaying Radio Information ........................ 39
Receiving RDS.............................................. 39
Listening to DAB Digital Radio ...................... 40
Presetting FM Stations Automatically
(Auto Preset) ..............................................43
Presetting AM/FM/DAB Stations Manually.... 44
Selecting Preset Stations .............................. 45
Clock and Timer
Setting the Clock ..............................................49
Setting AccuClock to Use a Specific
Station ........................................................49
Setting the Clock Manually ...........................50
Using the Timers ..............................................51
About the Timers ..........................................51
Programming the Timers ..............................52
Turning Timers On and Off ...........................54
Checking Timer Settings ..............................54
Using the Sleep Timer ..................................55
Miscellaneous
Troubleshooting ................................................56
Specifications ...................................................59
Advanced Operations
Connecting Other Components ........................19
About Connections .......................................19
Cables and Jacks .........................................19
Connecting a Subwoofer ..............................19
Connecting an Onkyo Cassette Deck ...........20
Connecting an Onkyo MD recorder ..............21
Connecting an Onkyo RI Dock
(Remote Interactive Dock) .........................22
Connecting an Onkyo CD Recorder
(CR-515DAB) .............................................23
Connecting a Portable Audio Device.............23
Connecting a Component with a Digital Audio
Output (CR-515DAB only) ..........................24
Connecting a TV ...........................................25
Memory Playback .........................................35
Random Playback ........................................36
Repeat Playback ..........................................36
Setting MP3 Preferences ..............................37
Selecting DAB Stations .................................41
Displaying DAB Radio Information ................41
DAB Setup.....................................................42
Naming Presets.............................................46
Copying Presets ............................................47
Erasing a Preset’s Name...............................48
Erasing Presets .............................................48
8
Getting to Know the CD Receiver
Front Panel
123 54
6 7 M N O98 J K L
123 54
6 P N OQ98 J MR
CR-515DAB
CR-315DAB
9
Getting to Know the CD Receiver
—Continued
The page numbers in parentheses show where you can find the main explanation for each item.
A
STANDBY indicator (25, 27)
Lights up in Standby mode.
B
STANDBY/ON button (27, 50, 53, 56)
Sets the CD receiver to On or Standby.
C
Remote control sensor (5)
Receives control signals from the remote controller.
D
Display
See “Display” on page 10.
E
VOLUME control (27)
Adjusts the volume level.
On the CR-515DAB, the volume control indicator
lights up when the CD receiver is on.
F
PHONES jack (27)
This stereo minijack is for connecting a pair of ste-
reo headphones for private listening.
G
LINE 2 IN jack (CR-515DAB)
This stereo minijack is for connecting an audio
source, such as an MP3 music player or personal
computer.
H
Disc tray (30)
The CD is loaded here.
I
INPUT button (27, 29, 43, 45)
Used to select the input source.
J
DIRECT button (28)
Used with the Direct function.
On the CR-515DAB, the DIRECT button’s indica-
tor lights up when the Direct function is on.
K
TONE button (CR-515DAB) (28)
Used to adjust the bass and treble.
L
Multi control (CR-515DAB) (30, 45)
Used to select radio presets, tracks, and MP3 fold-
ers. Also used to select and set various functions
and settings.
M
Eject [ ] button (30)
Ejects the loaded CD.
N
Stop [ ] button (30, 56)
Stops CD playback.
O
Play/Pause [ ] button (30)
Starts CD playback. Pressing it during playback
pauses playback.
P
LINE IN jack (CR-315DAB) (23)
This stereo minijack is for connecting an audio
source, such as an MP3 music player or personal
computer.
Q DISPLAY button (CR-315DAB) (31, 34, 39)
Used to change the information shown on the dis-
play. Also used to select characters when naming
radio presets.
R Previous and Next [ ]/[ ] buttons
(CR-315DAB) (30)
The Previous [ ] button selects the previous
track. During playback it selects the beginning of
the current track. The Next [ ] button selects the
next track.
/
10
Getting to Know the CD Receiver—Continued
A SLEEP indicator
Lights up when the Sleep function has been set.
B MP3 indicator
Lights up when an MP3 CD is loaded.
C PCM indicator
Lights up when the digital input signal received by
the DIGITAL IN jack is PCM. It flashes if the signal
is not PCM or the CD receiver is not locked to the
incoming digital signal.
D FOLDER indicator
Lights up while the number of an MP3 folder is
being displayed.
E DIRECT indicator
Lights up when the Direct function is on.
F S.BASS indicator
Lights up when the Super Bass function is on.
G MUTING indicator
Flashes while the CD receiver is muted.
H Playback mode indicators
1FOLDER: Lights up when 1-folder playback is
selected.
MEMORY: Lights up when memory playback is
selected.
RANDOM: Lights up when random playback is
selected.
REPEAT: Lights up when repeat playback is
selected for all tracks.
REPEAT 1: Lights up when repeat playback is
selected for one track.
I Play and pause indicators
The Play indicator lights up for playback. The
Pause indicator lights up while playback is paused.
J TIMER indicators
Show the status of the timers.
TIMER: Lights up when a timer has been pro-
grammed.
1, 2, 3, 4: Light up when a timer has been pro-
grammed.
: Lights up when a timer has been programmed
for recording.
K Tuning indicators
AUTO: Lights up when Auto Tuning is selected,
and disappears when Manual Tuning is selected.
: Lights up when the CD receiver is tuned
to a radio station.
DAB: Lights up when the CD receiver is tuned to a
DAB digital radio station.
FM ST: Lights up when the CD receiver is tuned to
a stereo FM station.
RDS (European model only): Lights up when
the CD receiver is tuned to a radio station that sup-
ports RDS (Radio Data System).
L FILE indicator
Lights up when an MP3 file number is being dis-
played.
M TRACK indicator
Lights up when a CD track number is being dis-
played.
N TITLE, ARTIST and ALBUM indicators
TITLE lights up when the title (ID3 tag) of an MP3
track is being displayed.
ARTIST lights up when the artist name from an
MP3 track (ID3 tag) is being displayed.
ALBUM lights up when the album name from an
MP3 track (ID3 tag) is being displayed.
O DISC, TOTAL, and REMAIN indicators
These indicators light up when the total time or the
remaining disc or track time is being displayed.
P Message area
Various information is displayed here, including
radio preset numbers, tuning frequency, current
time, volume level, sleep time, mode settings, and
so on.
Display
9 J K L M N O P
1243 5 6 7 8
/
11
Getting to Know the CD Receiver—Continued
The page numbers in parentheses show where you can find the main explanation for each item.
A LINE 1 IN (CR-515DAB) (25)
This analog audio input is for connecting a compo-
nent with an analog output, such as a TV, or a turn-
table with a built-in phono equalizer.
B MD/TAPE IN/OUT (20, 21)
These analog audio inputs and outputs are for con-
necting a recorder with an analog input and output,
such as a MiniDisc recorder or cassette deck.
C DAB ANTENNA (17)
This jack is for connecting a DAB antenna.
D AM ANTENNA (16, 17)
These push terminals are for connecting an AM
antenna.
E FM ANTENNA (16, 17)
This jack is for connecting an FM antenna.
F SUBWOOFER PRE OUT (19)
This jack is for connecting a powered subwoofer.
G DC OUT (CR-515DAB only)
This jack is for powering the Onkyo UWL-1 Wire-
less USB Audio Transport. Only connect the special
cable included with the UWL-1. Do not connect any
other cable, as it will cause a malfunction. See the
UWL-1’s instruction manual for more information.
H SPEAKERS (18)
These terminal posts are for connecting speakers.
I REMOTE CONTROL (20–24)
This (Remote Interactive) jack can be con-
nected to an jack on another Onkyo component.
The CD receiver’s remote controller can then be
used to control that component. To use , you
must make an analog audio connection (RCA)
between the CD receiver and the other component,
even if they are connected digitally.
J OPTICAL DIGITAL IN (CR-515DAB only) (24)
This optical digital audio input can be used to con-
nect a component with an optical digital output,
such as a CD recorder, MD recorder, games con-
sole, satellite tuner, or personal computer. Use a
commercially available optical digital audio cable
to make the connection.
K DOCK/CDR IN/OUT (CR-515DAB) (22, 23)
These analog audio inputs and outputs are for con-
necting a recorder with an analog input and output
such as a CD recorder, or an Onkyo RI Dock.
L AC INLET (25)
The supplied power cord is connected here.
M DOCK IN (CR-315DAB) (22)
This analog audio input is for connecting an Onkyo
RI Dock.
Rear Panel
12 H
M
74 5 6
I JK L
3
CR-515DAB CR-315DAB
See pages 16–25 for connection information.
12
Getting to Know the CD Receiver—Continued
Remote Controller
K
O
M
Q
R
T
S
P
U
V
B
A
3
5
J
4
L
6
7
N
8
9
K
O
M
Q
R
T
S
P
U
V
B
A
3
5
J
4
L
6
7
N
8
9
RC-662S
(CR-515DAB)
RC-660S
(CR-315DAB)
13
Getting to Know the CD Receiver—Continued
The page numbers in parentheses show where you can find the main explanation for each item.
A STANDBY/ON button (27, 53)
This button is used to set the CD receiver to On or
Standby.
B SLEEP button (55)
Used to set the Sleep timer, which turns off the CD
receiver after a specified time.
C Number buttons (31, 33, 35, 45, 46, 52)
Used to select tracks and radio presets. Also used to
set the clock manually, set the timers, and enter
names for radio presets. Can also be used with an
Onkyo RI Dock or CD recorder.
D TIMER button (26, 49, 50, 52, 54)
Used to set the timers and clock.
E MENU/NO/CLEAR button (29, 36, 42–44,
46–48)
Used with various functions and settings for select-
ing, cancelling, and deleting. With an Onkyo CD
recorder, it works as a clear button. With an Onkyo
RI Dock, it works as a mode button.
F Previous/Next [ ]/[ ] and
[ PRESET]/[PRESET ] buttons (31, 40,
42, 45)
Used to select the previous or next track or radio
preset. Can also be used with an Onkyo RI Dock or
CD recorder. With an Onkyo cassette deck, they
work as rewind and fast forward buttons.
G Rewind/Fast Forward [ ]/[ ] and
[ TUN]/[TUN ] buttons (31, 38, 41, 49)
Used to rewind or fast forward CD playback. Can
also be used with an Onkyo RI Dock or CD
recorder. Also used to tune the radio and edit preset
names.
H CD control buttons (31)
:Pauses playback.
: Stops playback.
: Starts playback.
I VOLUME [ / ] buttons (27, 31)
Adjust the volume level.
J S.BASS button (28)
Sets the Super Bass function.
K Onkyo RI Dock and CD recorder control
buttons
:Pauses playback or recording.
: Stops playback or recording.
: Starts playback or resumes recording.
L Onkyo MD recorder and cassette deck
control buttons
For twin cassette decks, only Deck B can be con-
trolled.
: Plays side B (cassette deck).
:Pauses playback or recording (MD).
: Stops playback, recording, fast-forward, or
rewind.
: Plays side A.
M CLOCK CALL button (50)
Calls up the clock to display the day and time.
N INPUT [ ]/[ ] buttons (27, 29, 43, 45)
Used to select the input source.
O DISPLAY button (31, 34, 39, 41, 46, 50)
Used to change the information shown on the dis-
play. Also used to select characters when naming
radio presets. Can also be used with an Onkyo CD
recorder. With an Onkyo RI Dock, it works as a
backlight button.
P FOLDER button (32, 33, 34, 37)
Used to select MP3 folders.
Q REPEAT button (36)
Sets repeat playback. Can also be used with an
Onkyo CD recorder. With an Onkyo cassette deck,
it works as a reverse mode button.
R TONE button (28)
Used to adjust the bass and treble.
S YES/MODE/SHUFFLE button (34–36, 38)
Used with various functions and settings for con-
firming, selecting modes, and selecting shuffle play-
back.
T ENTER button
Used to confirm various functions and settings. Can
also be used with an Onkyo RI Dock or CD
recorder.
U MUTING button (28)
Mutes the output of the CD receiver.
V TUNER/BAND button (38, 40, 43, 44, 45)
Selects AM, FM, or DAB radio as the input source.
14
Disc Notes
Supported Discs
The CD receiver supports the following discs.
Some audio CDs use copy protection that doesn’t con-
form to the official CD standard. Since these are non-
standard discs, they may not play properly in the CD
receiver.
The CD receiver supports CD-R and CD-RW discs.
However, some CD-R and CD-RW discs may not
work properly for any of the following reasons: disc
burner characteristics, disc characteristics, the disc is
damaged or dirty. See the manual supplied with your
disc burner for more information. Condensation or
dirt on the optical pickup lens can also affect play-
back.
The CD receiver supports 8 cm and 12 cm discs.
The CD receiver does not support disc types not listed.
Don’t use discs with an unusual shape, such as those
shown below, as you may damage the CD receiver.
Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custom-
made labels or stickers. Doing so may damage the CD
receiver and you may not be able to remove the disc
properly.
Discs Made on Personal Computers
Discs made on personal computers, including those of a
compatible format, may not work properly in the CD
receiver because of incorrect settings in the disc burning
software. Check the manuals supplied with your disc
burning software for additional compatibility informa-
tion.
MP3 Compatibility
MP3 discs must be ISO 9660 Level 1 or Level 2,
Romeo or Joliet compliant. Supported formats:
Mode 1, Mode 2 XA Form 1.
•Folders can be up to eight levels deep.
MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with a sampling rate of between 8 kHz and
48 kHz and a bit-rate of between 8 kbps and 320 kbps
(128 kbps recommended). Incompatible files cannot
be played.
Constant bit rate MP3 files are recommended, how-
ever, variable bit-rate (VBR) MP3 files between
8 kbps and 320 kbps are supported. (Playing times
may not display correctly.)
MP3 files must have a “.mp3” or “.MP3” file name
extension. MP3 files without the proper extension will
not be recognized. To prevent noise and malfunction,
do not use these extensions for other types of files.
The CD receiver supports up to 499 MP3 files and
folders. Files and folders in excess of this cannot be
played. Note that if the file and folder structure is very
complicated, the CD receiver may not be able to read
or play all of the MP3 files on the disc.
Disc, file, and folder names may contain up to 32 char-
acters.
The maximum time that can be displayed for a single
file is 99 minutes and 59 seconds.
The remaining time cannot be displayed when playing
MP3 files.
MP3 file and folder names (excluding the extension)
are shown on the display.
Multisession discs are supported, however, some mul-
tisession discs may take a long time to load and some
may not load at all. When burning CDs, we recom-
mend that you use a single-session (disc-at-once), and
select “Disc Close.
Normally, the music in the audio session of a CD
Extra disc is played. However, you can set the CD
receiver so that it plays any MP3 files in the data ses-
sion of a CD-R/RW disc instead. If the data session
contains no MP3 files, the audio session will be played
regardless. See “Setting MP3 Preferences” on page 36
for more information.
The Emphasis is not supported.
Disc Logo Format or file type
Audio CD PCM
CD-R
Audio CD, MP3
MP3
CD-RW
Audio CD, MP3
MP3
CD Extra
Audio CD (Session 1),
MP3 (Session 2)
15
Disc Notes—Continued
The following ID3 tags are supported: versions
1.0/1.1 and 2.2/2.3/2.4. Versions 2.5 and later are not
supported. Normally, version 2.2/2.3/2.4 tags have
priority and will be displayed regardless of the ID3
VER 1 preference on page 37.
•For ID3 version 2 tags, the tag information recognized
will be those embedded in the beginning of the file.
We recommend that you include only title, artist
name, and album name information in ID3 tags. Com-
pressed, encrypted, and unsynchronized ID3 tags can-
not be displayed.
Note:
With CD-ROM, CD-R, and CD-RW discs that contain
many files and folders and files other than MP3s, it may
take a long time to read the disc. We recommend that you
include only MP3 files on your discs, use about 20 fold-
ers, and limit folder nesting to three levels deep.
Disc Content Organization
CD
CDs contain tracks.
MP3
MP3 discs contain MP3 files organized into folders.
Handling Discs
•Never touch the underside of a disc. Always hold discs
by the edge, as shown.
•Never attach adhesive tape or sticky labels to discs.
Cleaning Discs
•For best results, keep your discs clean. Fingerprints
and dust can affect the sound quality and should be
removed as follows. Using a clean soft cloth, wipe
from the center outwards, as shown. Never wipe in a
circular direction.
•To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
•Never use solvent-based cleaning fluids, such as thin-
ner or benzine, commercially available cleaners, or
antistatic sprays intended for vinyl records, as they
may damage the disc.
Storing Discs
Don’t store discs in places subject to direct sunlight or
near heat sources.
Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
•Always store discs in their cases and vertically. Stack-
ing, or putting objects on unprotected discs may cause
warping, scratches, or other damage.
Track 2 Track 3 Track 4Track 1
Audio CD
Track 5
Folder 1
Folder 2
File 2 File 3 File 1File 1 File 2
MP3 (CD-R/CD-RW)
Underside
16
Connecting Antennas
This section explains how to connect the supplied indoor
FM antenna, AM loop antenna, and DAB antenna, and
how to connect commercially available outdoor FM and
AM antennas.
The CD receiver won’t pick up any radio signals without
an antenna connected, so you must connect the antenna
to use the tuner.
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 17).
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 17).
1
Attach the FM antenna, as shown.
North American Model
Other Models
Once the CD receiver is ready for use, you’ll need
to tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to
fix the FM antenna into position.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
AM antenna push terminals
FM antenna jack
DAB antenna
jack
Insert the plug fully
into the jack.
Insert the plug fully
into the jack.
Thumbtacks, etc.
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Once the CD receiver is ready for use, you’ll need
to tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from the
CD receiver, TV, speaker cables, and power cords.
Push Insert wire Release
17
Connecting Antennas—Continued
Connecting the DAB Antenna
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
Notes:
Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in
an attic or loft.
•For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
•For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor AM antennas work best when installed horizon-
tally outside, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
1
Screw the supplied DAB antenna’s plug
onto the DAB ANTENNA jack.
Once the CD Receiver is ready for use, you’ll
need to tune into a DAB station and adjust the
position of the DAB antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to
fix the DAB antenna into position.
To CD receiver To TV (or VCR)
TV/FM antenna splitter
Outdoor antenna
AM loop antenna
Insulated antenna cable
18
Connecting Speakers
Connecting Your Speakers
Connect the right speaker to the CD receiver’s right (R) SPEAKERS terminals. Connect the left speaker to the left
(L) SPEAKERS terminals.
Connect the positive (+) terminal on each speaker to the corresponding positive (+) terminal on the CD receiver.
Connect the negative (–) terminal on each speaker to the corresponding negative (–) terminal on the CD receiver. Use
the red wires to connect the positive (+) terminals.
Connect only speakers with an impedance of between
4 and 16 ohms. Connecting a speaker with a lower
impedance may damage the speaker.
Be careful not to short the positive and negative wires.
Doing so may damage the CD receiver.
Do not connect both speaker cables to the same L or R
terminals (Fig. 1). Do not connect more than two
speaker terminals to each speaker (Fig. 2).
SPEAKERS
R
L
—Push-type terminals—
Strip about 10 mm (3/8") of insulation from the ends of the speaker
cables, and twist the bare wires tightly. Push the lever and insert the
bare wires. Release the lever. Make sure the terminal is gripping the
bare wires and not the insulation.
Red wires
Right speaker
Left speaker
Speaker
cable
—Terminal posts—
Strip about 15 mm (5/8") of insulation from the ends of the speaker
cables, and twist the bare wires tightly. Unscrew the terminal. Fully
insert the bare wire, making sure that it’s touching the threaded shaft in
the center. Screw the terminal tight.
SPEAKERS
R
L
R
L
Fig. 1 Fig. 2
19
Connecting Other Components
Before making any connections, read the manuals
supplied with your other components.
Don’t connect the power cord until you’ve completed
and double-checked all connections.
Connection Color Coding
RCA-type audio connections are usually color-coded:
red and white. Use red plugs to connect right-channel
audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and out-
puts (typically labeled “L”).
Push plugs in all the way to make
good connections (loose connec-
tions can cause noise or malfunc-
tions).
•To prevent interference, keep
audio cables away from power
cords and speaker cables.
Optical Digital Jack (CR-515DAB)
The CD receiver’s optical digital jack has a shutter-type
cover that opens when an optical plug is inserted and
closes when it’s removed. Push the plug in all the way.
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
Note:
Do not put anything on top of the CD receiver, as it may
interfere with proper ventilation.
No connecting cables are included with the CD receiver.
The CD receiver has a SUBWOOFER PRE OUT jack for connecting a powered subwoofer (i.e., a subwoofer with a
built-in amplifier).
About Connections
Left (white)
Right (red)
Analog audio
cable
Left (white)
Right (red)
Right!
Wrong!
Cables and Jacks
Cable Jack Description
Analog audio
cable (RCA)
This cable carries analog audio.
Optical digital
audio cable
This cable carries digital audio.
Stereo miniplug
cable
This cable carries analog audio.
R
L
OPTICAL
Connecting a Subwoofer
: Signal flow
Powered subwoofer
CD receiver
20
Connecting Other Components—Continued
The following diagram shows how to connect an optional Onkyo cassette deck.
Connect the CD receiver’s MD/TAPE OUT jacks to the cassette deck’s INPUT (REC) jacks, and connect the CD
receiver’s MD/TAPE IN jacks to the cassette deck’s OUTPUT (PLAY) jacks.
What can you do with ?
Connecting an Onkyo cassette deck to the CD receiver with an cable allows you to control the cassette deck with
the CD receiver’s remote controller. In addition, when playback is started on the cassette deck, the CD receiver will
automatically select it as the input source.
•To use , you must connect the Onkyo cassette deck to the CD receiver with an cable and an analog audio
cable (RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “TAPE.” Since this is the default
setting, unless you’ve changed it, it can be left as it is (see page 29).
Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
Connecting an Onkyo Cassette Deck
IN
IN
OUT
R
DOCK
MD/
TAPE
L
IN
IN
R
LINE 1
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
(REC) (PLAY)
INPUT OUTPUT
REMOTE
CONTROL
L
R
(REC) (PLAY)
INPUT OUTPUT
REMOTE
CONTROL
L
R
: Signal flow
Onkyo cassette deck’s
rear panel
Analog audio cables (RCA)
cable supplied with
the Onkyo cassette deck
White
Red
White
Red Red
Red
White White
CR-515DAB’s
rear panel
CR-315DAB’s
rear panel
Onkyo cassette deck’s
rear panel
Analog audio cables (RCA)
cable supplied with
the Onkyo cassette deck
White
Red
White
Red
Red
White WhiteRed
21
Connecting Other Components—Continued
The following diagram shows how to connect an optional Onkyo MD recorder.
Connect the CD receiver’s MD/TAPE OUT jacks to the MD recorder’s INPUT (REC) jacks, and connect the CD
receiver’s MD/TAPE IN jacks to the MD recorder’s OUTPUT (PLAY) jacks.
What can you do with ?
Connecting an Onkyo MD recorder to the CD receiver with an cable allows you to control the MD recorder with
the CD receiver’s remote controller. In addition, when playback is started on the MD recorder, the CD receiver will
automatically select it as the input source.
•To use , you must connect the Onkyo MD recorder to the CD receiver with an cable and an analog audio cable
(RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “MD” (see page 29).
Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
Note:
The MD/TAPE jacks can alternatively be used to connect a VCR or DAT recorder, in which case the Input Display
on the CD receiver would need to be set to “VCR” or “DAT” respectively (see page 29).
Connecting an Onkyo MD recorder
IN
IN
OUT
R
DOCK
MD/
TAPE
L
IN
IN
R
LINE 1
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
(REC) (PLAY)
INPUT OUTPUT
REMOTE
CONTROL
L
R
(REC) (PLAY)
INPUT OUTPUT
REMOTE
CONTROL
L
R
: Signal flow
Onkyo MD recorder’s
rear panel
Analog audio cables (RCA)
cable supplied with
the Onkyo MD recorder
White
Red
White
Red Red
Red
White White
CR-515DAB’s
rear panel
CR-315DAB’s
rear panel
Onkyo MD recorder’s
rear panel
Analog audio cables (RCA)
cable supplied with
the Onkyo MD recorder
White
Red
White
Red
Red
White WhiteRed
22
Connecting Other Components—Continued
The following diagram shows how to connect an optional Onkyo RI Dock (Remote Interactive Dock).
Connect the CD receiver’s DOCK/CDR IN jacks (DOCK IN jacks on the CR-315DAB) to the RI Dock’s AUDIO OUT
jacks.
What can you do with ?
Connecting an Onkyo RI Dock to the CD receiver with an cable allows you to control the RI Dock with the CD
receiver’s remote controller. In addition, when playback is started on the RI Dock, the CD receiver will automatically
select it as the input source.
•To use , you must connect the RI Dock to the CD receiver with an cable and an analog audio cable (RCA).
On the RI Dock, set the MODE switch to “HDD.” See the RI Dock’s instruction manual for details.
CR-515DAB
•To use , the Input Display for the DOCK/CDR jacks must be set to “DOCK.” Since this is the default setting,
unless you’ve changed it, it can be left as it is (see page 29).
Connecting an Onkyo RI Dock (Remote Interactive Dock)
IN
IN
OUT
R
DOCK
MD/
TAPE
L
IN
IN
R
LINE 1
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
R
AUDIO OUT DC INS VIDEO OUT
----
L
R
AUDIO OUT DC INS VIDEO OUT
----
L
: Signal flow
CR-515DAB’s
rear panel
White
Red
Red
White
Analog audio cable (RCA)
cable supplied
with the RI Dock
Onkyo RI Dock’s rear
panel
CR-315DAB’s
rear panel
White
Red
Red
White
Analog audio cable (RCA)
cable supplied
with the RI Dock
Onkyo RI Dock’s rear
panel
23
Connecting Other Components—Continued
The following diagram shows how to connect an optional Onkyo CD recorder.
Connect the CD receiver’s DOCK/CDR OUT jacks to the CD recorder’s INPUT (REC) jacks, and connect the CD
receiver’s DOCK/CDR IN jacks to the CD recorder’s OUTPUT (PLAY) jacks.
What can you do with ?
Connecting an Onkyo CD recorder to the CD receiver with an cable allows you to control the CD recorder with
the CD receiver’s remote controller. In addition, when playback is started on the CD recorder, the CD receiver will
automatically select it as the input source.
•To use , you must connect the Onkyo CD recorder to the CD receiver with an cable and an analog audio cable
(RCA). In addition, the Input Display for the DOCK/CDR jacks must be set to “CDR” (see page 29).
Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
The following diagram shows how to connect a portable audio device (e.g., MP3 player, MD player, CD player).
Connect the CD receiver’s LINE 2 IN jack (LINE IN jack on the CR-315DAB) on the front panel to the portable audio
device’s output jack.
Depending on the type of output jack on the portable audio device, you may need to buy a suitable cable. The CD
receiver’s LINE 2 IN jack (LINE IN jack on the CR-315DAB) accepts a stereo miniplug.
Notes:
Use a connecting cable that doesn’t have any attenuation resistors in it.
If you connect a portable audio device’s headphone output to the CD receiver’s LINE2 IN jack (LINE IN jack on the
CR-315DAB), turn down the volume on the portable audio device before you connect it.
When you connect a portable audio device to the CD receiver, make sure you connect it to the LINE 2 IN jack (LINE
IN jack on the CR-315DAB) and not the adjacent PHONES jack. If you connect to the PHONES jack by mistake, it
may cause the PHONES output to malfunction.
Connecting an Onkyo CD Recorder (CR-515DAB)
Connecting a Portable Audio Device
IN
IN
R
LINE 1
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
(REC) (PLAY)
INPUT OUTPUT
REMOTE
CONTROL
L
R
: Signal flow
Onkyo CD recorder’s
rear panel
Analog audio cable (RCA)
cable supplied with
the Onkyo CD recorder
White
Red
White
Red Red
Red
White White
CR-515DAB’s
rear panel
: Signal flow
CR-515DAB’s front panel
Stereo miniplug cable
Portable audio device’s output jack
24
Connecting Other Components—Continued
The following diagram shows how to connect a component with an optical digital audio output, such as a CD recorder,
MD recorder, games console, satellite tuner, or personal computer.
Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the other component.
You can change the Input Display for the OPTICAL DIGITAL IN to DIGITAL, CDR, PC, or GAME so that it matches
the type of component that you connect (see page 29).
Connecting an Onkyo Component with a Digital Audio Output
The following diagram shows how to connect an Onkyo component with an optical digital audio output.
Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the Onkyo component.
What can you do with ?
Connecting an Onkyo component to the CD receiver with an cable allows you to control the component with the
CD receiver’s remote controller. In addition, when playback is started on the component, the CD receiver will auto-
matically select it as the input source.
•To use , you must connect the Onkyo component to the CD receiver with an cable and an analog audio cable
(RCA). In addition, you must change the Input Display for the DIGITAL IN so that it matches the type of component
that you connect. When you connect a CD recorder to the DOCK/CDR jacks and OPTICAL DIGITAL IN jack, you
must set the Input Display for DOCK/CDR to “CD-R,” and set the Input Display for OPTICAL DIGITAL IN to
“CD-R/dig” (see page 29).
If you connect an audio processor such as the Onkyo UE-205, you must set the Input Display for DOCK/CDR to
“PC,” and set the Input Display for OPTICAL DIGITAL IN to “PC/dig,” otherwise the wrong input source may be
selected when playback starts (see page 29).
Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
Connecting a Component with a Digital Audio Output (CR-515DAB only)
DIGITAL
OUTPUT
Satellite tuner, CD
recorder, etc.
Optical digital audio cable
: Signal flow
CR-515DAB’s
rear panel
Personal computer
IN
R
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
REMOTE
CONTROL
DIGITAL
OUTPUT
(REC) (PLAY)
INPUT OUTPUT
L
R
Onkyo component with a
digital audio output
cable
: Signal flow
Optical digital audio cable
CR-515DAB’s
rear panel
Analog audio cable (RCA)
Red
White
White
Red Red
Red
White White
25
Connecting Other Components—Continued
Connect the CD receiver’s LINE 1 IN jacks (use the DOCK IN jacks on the CR-315DAB) to the TV’s audio output
jacks.
Hint:
To listen to the TV, select the LINE 1 input source (select DOCK on the CR-315DAB).
Notes:
Before connecting the power cord, connect all of your speakers and AV components.
•Turning on the CD receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the CD receiver into a different branch circuit.
Do not use a power cord other than the one supplied with the CD receiver. The supplied power cord is designed
exclusively for use with the CD receiver and should not be used with any other equipment.
•Never disconnect the power cord from the CD receiver while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the CD receiver.
To set the clock with the AccuClock function, the CD receiver must be able to receive RDS radio stations, which means
an FM antenna must be connected (see page 16).
Connecting a TV
IN
IN
R
LINE 1
MD/
TAPE
L
IN
OUT
OUT
DOCK/
CDR
: Signal flow
CR-515DAB’s
rear panel
White
Red
Red
White
Analog audio cable (RCA)
TV
Connecting the Power Cord
1
2
1
2
To wall outlet
Supplied power cord
CR-315DABCR-515DAB
To wall outlet
Supplied power cord
1
Connect the supplied power cord to the CD receiver’s AC INLET.
2
Plug the power cord into a suitable wall outlet.
The STANDBY indicator lights up.
26
First Time Setup (European Model Only)
To use the AccuClock function, the CD receiver must be able to receive RDS radio stations, which means an FM antenna
must be connected. Be sure to connect an FM antenna before attempting to use this function (see page 16).
The very first time you turn on the CD receiver, the AccuClock function automatically sets the CD receiver’s clock based
on the CT (Clock Time) information present in an RDS radio broadcast. While the clock is being set, “Wait…” flashes
on the display, as shown. Note that it may take up to 5 minutes to set the clock.
When the clock has been set, the message “Clock Adjusted” scrolls across the display, then the day and time are dis-
played for a while, as shown.
The AccuClock function automatically updates the clock daily at 2 A.M., 3 A.M., and 2 P.M.
If for some reason the clock cannot be set automatically, see “Setting AccuClock to Use a Specific Station” on page 49
and “Setting the Clock Manually” on page 50.
Turning Off the AccuClock Function
If you don’t want AccuClock to automatically update the clock each day, you can turn it off as follows.
Note:
The AccuClock function cannot be turned off until the
clock has been set.
Setting the Clock with the AccuClock Function (European Model Only)
YES/MODE
ENTER
TIMER
1
Press the [TIMER] button repeat-
edly until “Clock” appears on the
display.
2
Press [ENTER].
“*AccuClock*” appears on the display.
3
To turn off AccuClock, press the
[YES/MODE] button.
The asterisks disappear, indicating that
the AccuClock function is off. To turn
AccuClock back on again, press the
[YES/MODE] button so that the aster-
isks are displayed.
The asterisks indicate that the
AccuClock function is on.
27
Basic Operation
To turn on the CD receiver, press the [STANDBY/ON]
button on the CD receiver or remote controller. The
STANDBY indicator goes off.
Press the [STANDBY/ON] button again to set the CD
receiver to Standby. The STANDBY indicator lights up.
Tip:
When you start playback on (or turn on) an Onkyo RI
Dock, CD recorder, MD recorder, or cassette deck that’s
connected to the CD receiver with an cable and ana-
log audio cable, the CD receiver turns on automatically.
Similarly, when you set the CD receiver to On or
Standby, the other component will also be set to On or
Standby.
Turn the [VOLUME] control clockwise to increase the
volume or counterclockwise to decrease it.
You can also use remote controller’s VOLUME
[ ]/[ ] buttons.
You can select CD, DAB, AM, FM, or a connected com-
ponent (TAPE, DOCK, LINE, DIGITAL) as the input
source.
To select the input source, press the remote controller’s
INPUT [ ]/[ ] buttons repeatedly. On the CD
receiver, press the [INPUT] button repeatedly. The input
sources are selected in the following order.
*1 Input Display can be changed (see page 29).
*2 CR-515DAB only.
Turn down the volume, then connect your stereo head-
phones to the PHONES minijack.
You can adjust the volume and mute the sound, as
explained earlier.
The speakers output no sound while the headphones are
connected.
VOLUME
/
STANDBY/
ON
INPUT
/
VOLUMESTANDBY/ON
INPUTPHONES
STANDBY indicator
Turning On the CD Receiver
Adjusting the Volume
Remote
controller
CD receiver
Remote
controller
CD receiver
Selecting the Input Source
Using Headphones
CD
DIGITAL FMDAB
DAB
AM
LINE1LINE2
TAPE
*
1
DOCK
*
1
*
1,
*
2
CD FM AM
DOCK
TAPE
LINE
*
1
CR-515DAB
CR-315DAB
PHONES jack
28
Basic Operation—Continued
On the CR-515DAB, you can also use the [TONE] but-
ton and multi control on the front panel to adjust the bass
and treble.
To turn on the Super
Bass function, press
the [S.BASS] button.
The S.BASS indicator lights
up.
To turn off the Super Bass function, press the [S.BASS]
button again.
On the CR-515DAB, you can also use the [TONE] but-
ton on the front panel. Press the [TONE] button for 3
seconds to turn on the Super Bass function.
Note:
If you press the [S.BASS] button while the Direct func-
tion is on, the Direct function will be turned off.
To turn the Direct function on or off, press
the [DIRECT] button on the CD receiver.
When the Direct function is off, the tone
controls can be used to adjust the sound.
When the Direct function is on, the tone
controls are bypassed, so you can enjoy a
pure sound, and the DIRECT indicator lights up.
On the remote controller, press the [TONE] button for 3
seconds to turn on the Direct function.
On the CR-515DAB, the [DIRECT] button’s indicator
lights up when the Direct function is on.
To mute the output of the
CD receiver, press the
remote controller’s [MUT-
ING] button. The MUTING
indicator flashes on the dis-
play.
On the CR-515DAB, the volume control indicator
flashes, too.
To unmute the CD receiver, press the [MUTING] button
again.
Tips:
While the CD receiver is muted:
•Turning the [VOLUME] control on the CD receiver or
pressing the VOLUME [ ]/[ ] buttons on the
remote controller will unmute the CD receiver.
If you turn the CD receiver off, the next time you turn
it on, the CD receiver will be unmuted.
MUTING
S.BASS
/
TONE
ENTER
DIRECT
DIRECT TONE
CR-515DAB
CR-315DAB
Adjusting the Bass and Treble
1
Press the [TONE] button to select
Bass.
2
Use the Previous and Next
[ ]/[ ] buttons to adjust the
bass.
The default setting is “±0.You can
adjust the bass and treble from –3 to +3.
Press [ENTER], and then use the
Previous and Next [ ]/[ ] but-
tons to adjust the treble.
Notes:
If you press no buttons for 8 seconds,
the previous display will appear auto-
matically.
If you press the [TONE] button while
the Direct function is on, the Direct
function will be turned off.
Using the Super Bass Function
Using the Direct Function
Muting the Sound
DIRECT indicator
MUTING indicator
29
Basic Operation—Continued
You can choose what name is displayed when an input source is selected so that it matches the type of component that
you’ve connected to the MD/TAPE IN, DOCK/CDR IN, or DIGITAL IN. When you connect an Onkyo -capable
component, it’s important that you select the input source name that matches the type of component for to work
properly.
On the CR-515DAB, you can also use the front panel
controls.
1 Use the [INPUT] button to select the input source
whose name you want to change.
2 Push the multi control to select “Name Select?,” and
then push it again.
3Turn the multi control to select the new input source
name.
4 Push the multi control to confirm your selection.
Input Source Name Abbreviations
Sometimes the input source name may be displayed as a
2-letter abbreviation, as per the following table.
Changing the Input Display
1
Use the INPUT [ ]/[ ] buttons
to select the input source whose
name you want to change.
CR-515DAB: TAPE, DOCK, DIGI-
TAL
CR-315DAB: TAPE
2
Press and hold the
[MENU/NO/CLEAR] button until
“Name Select?” flashes on the
display, and then press [ENTER].
3
Use the Previous or Next
[ ]/[ ] button to select the
new input source name.
/
YES/MODE
MENU/NO/
CLEAR
ENTER
INPUT
/
Depending on the input source selected
in step 1, the input source names are
selected in the following orders:
4
Press [ENTER] to confirm your
selection.
“Complete” appears on the display.
Full name Abbreviation
CDR CR
DAT DT
DIGITAL DG
GAME GM
DOCK DC
LINE LI
LINE1 L1
LINE2 L2
MD MD
PC PC
TAPE TP
VIDEO VD
MDTAPE VIDEO
DAT
DOCK CD-R
PC
DIGITAL CD-R/dig
GAME/dig PC/dig
30
Playing CDs
Selecting Tracks (CR-515DAB)
To return to the beginning of the track
currently playing, turn the multi control
a little to the left.
Turn the multi control further to select
earlier tracks.
While playback is stopped, turn the multi control to
the left to select the previous track.
Turn the multi control to the right to select subse-
quent tracks.
On MP3 CDs, you can select MP3 files in other fold-
ers (see page 32).
Selecting Tracks (CR-315DAB)
To return to the beginning of the
track currently playing, press the
Previous [ ] button.
Press the Previous [ ] button
repeatedly to select earlier tracks.
While playback is stopped, pressing the Previous
[] button will select the previous track.
Press the Next [ ] button repeatedly to select sub-
sequent tracks.
On MP3 CDs, you can select MP3 files in other fold-
ers (see page 32).
/
/
Display
Disc tray
CR-515DAB CR-315DAB
Display
Disc tray
1
Press the Eject [ ] button to open
the disc tray.
Tip:
Pressing the Eject [ ] button while the
CD receiver is on Standby will turn on
the CD receiver and open the disc tray.
2
Place the CD on the tray with the
label-side facing up.
Place 8 cm CDs in the center of the tray.
3
To start playback, press the
Play/Pause [ ] button.
The disc tray closes and playback starts.
To stop playback:
Press the Stop [ ] button. Playback
stops automatically when the last track
has been played.
To pause playback:
Press the Play/Pause [ ] button.
The Pause indicator appears. To
resume playback, press the Play/Pause
[] button again.
To remove the CD:
Press the Eject [ ] button to open the
disc tray.
/
/
/
Total number
of tracks
Total playing
time
“DISC TOTAL” lights up
while the disc informa-
tion is being displayed.
Audio CD Display
Total number
of folders
Total number
of files
Disc name
MP3 CD Display
31
Playing CDs—Continued
During playback or while playback is paused, press the remote controller’s [DISPLAY] button repeatedly to display the
following CD information.
On the CR-315DAB, you can also use the CD receiver’s [DISPLAY] button to display this information.
Using the Remote Controller
To select:
Use the number buttons as
shown in the examples below to
select tracks.
Press to stop playback
Press to pause playback
To resume playback, press the Pause
[] or Play [ ] button.
Press:
Press to select tracks
Press the Previous [ ] button to
locate the beginning of the currently
playing or paused track. Press it
repeatedly to select earlier tracks.
Press the Next [ ] button repeat-
edly to select subsequent tracks.
On MP3 CDs, you can select files in
other folder
s (see page 32).
Press to adjust the volume
Press the VOLUME Up [ ] button to
turn up the volume. Press the VOLUME
Down [ ] button to turn it down.
Press to start playback
Pressing this button while the CD
receiver is on Standby will turn on the
CD receiver and start playback.
Press to display more CD infor-
mation
Tra ck #8
Used to enter numbers over 10.
With MP3 CDs, you can select files in
the current folder with these buttons.
Tra ck #10
Tra ck #34
Press to fast forward or fast
reverse
During playback or while playback is
paused, press and hold the Fast For-
ward [ ] button to fast forward, or the
Reverse [ ] button to fast reverse.
Displaying CD Information
Lights up while the elapsed track time
is being displayed.
“REMAIN”
Lights up while the remaining track
time is being displayed.
“TOTAL REMAIN”
Lights up while the remaining disc
time is being displayed.
During random playback, or if the total
time is more than 99 minutes and 59
seconds, “– –:– –” is displayed.
Note:
See page 34 for details on dis-
playing MP3 information.
32
Playing CDs—Continued
On an MP3 CD, MP3 files may be organized in a hierar-
chically, with folders containing files and subfolders, as
shown below. On the CD receiver, there are two modes
for selecting MP3 files: Navigation mode and All Folder
mode. In Navigation mode, you can select MP3 files by
navigating through the folder hierarchy, moving in and
out of folders and subfolders. In All Folder mode, all
folders appear at the same level, making it easy to select
folders regardless of the hierarchy.
If you don’t select a specific MP3 file or folder for play-
back, all of the MP3 files on the CD will be played in
numerical order starting with file #1.
Selecting MP3 Files in Navigation Mode
With Navigation mode, you can select MP3 files by nav-
igating through the folder hierarchy. This mode can only
be used while playback is stopped.
If random mode or 1-folder mode is currently selected,
press the [YES/MODE] button to cancel it before pro-
ceeding.
On the CR-515DAB, you can also use the multi control
for steps 2, 3, and 4. Turn the multi control to select files
and folders, and push it for ENTER.
Selecting MP3 Files
File #11
File #1
File #10
Folder #3
File #12
Root Folder #1
Folder #2
File #13
Folder #4
File #14
File #18
/
FOLDER
MENU/NO
ENTER
1
While playback is stopped, press
the [FOLDER] button.
The CD receiver enters Navigation
mode and “Root” appears on the dis-
play.
2
Press [ENTER].
The name of the first folder one level
down from root appears on the display.
If the disc contains no folders, the name
of the first MP3 file is displayed.
3
Use the Previous and Next
[ ]/[ ] buttons to select
other folders and files at the
same level.
Folders that don’t contain MP3 files or
subfolders can’t be selected.
4
To access files or subfolders
inside another folder, select the
folder, and then press [ENTER].
Use the Previous and Next
[ ]/[ ] buttons to select the files
and subfolders within that folder.
To move up a level, press the
[MENU/NO] button.
5
To start playback, press the
[ENTER] or Play/Pause [ ]
button.
Playback will start with the specified
file or folder and continue until all of
the MP3 files on the disc have been
played.
/
33
Playing CDs—Continued
Selecting MP3 Files in All Folder Mode
With All Folder mode, you don’t have to navigate the
folder hierarchy because all folders that contain MP3
files appear at the same level.
If random playback is currently selected, press the
[YES/MODE] button to cancel it before proceeding.
On the CR-515DAB, you can also use the multi control
for steps 2, 3, and 4. Turn the multi control to select files
and folders, and push it for ENTER.
To select an MP3 file in another folder during playback,
press the [FOLDER] button, select the folder by using
the Previous and Next [ ]/[ ] buttons (or multi
control), and then press [ENTER] (or push the multi
control). Now use the Previous and Next [ ]/[ ]
buttons (or multi control) to select the MP3 files within
that folder.
Pausing Playback
To pause playback, press the Play/Pause [ ] button.
To resume playback, press it again.
Cancelling Navigation or All Folder Mode
To cancel Navigation mode or All Folder mode while
selecting MP3 files, press the Stop [ ] button.
Selecting MP3 Folders and Files by Number
1 Press the [FOLDER] button for 2 seconds to
enter All Folder mode.
2 Use the number buttons as shown in the examples
below to enter folder numbers.
If playback is stopped, playback starts with the first
MP3 file in the specified folder. If playback is
already in progress,
press [ENTER]
to play the first
MP3 file in the specified folder.
3 Use the number buttons to enter the file number.
Playback starts.
If a folder contains more than 99 MP3 files, single-
and double-digit file numbers must be preceded by
zeros. For example, to specify file #5, press [5]. To
specify file #32, press [>10], [3], and [2].
1
While playback is stopped, press
the [FOLDER] button for 2 sec-
onds.
The CD receiver enters All Folder
mode and the name of the first folder
appears on the display.
2
Use the Previous and Next
[ ]/[ ] buttons to select the
other folders.
You can select any folder that contains
MP3 files.
To play the first file in the selected
folder, go to Step 4.
3
To access the files inside the
folder, press the [FOLDER] but-
ton.
The name of the first MP3 file inside
the folder is displayed.
Use the Previous and Next
[ ]/[ ] buttons to select the MP3
files within the folder.
To select another folder, press the
[FOLDER] button again, and then use
the Previous and Next [ ]/[ ]
buttons to select it.
/
FOLDER
ENTER
Number
buttons
4
To start playback, press the
[ENTER] or Play/Pause [ ]
button.
Playback will start with the specified
file or folder and continue until all of
the MP3 files on the disc have been
played.
/
/
To select: Press:
Folder #8
Used to enter numbers over 10.
Folder #10
Folder #34
34
Playing CDs—Continued
Playing the MP3 Files in Only One Folder
Normally, all of the MP3 files in all of the folders on the
disc are played. With 1-folder playback, only the MP3
files in the specified folder are played.
You can display various information about the MP3 file
currently playing, including ID3 tags such as title, artist
name, and album name.
Elapsed time: The length of time that the current MP3
file has been playing (default display). If the elapsed
time is more than 99 minutes and 59 seconds, “– –:– –”
is displayed.
File name: Name of the current MP3 file.
Folder name: Name of the current folder.
Title name: Title of the current file (if ID3 tag present).
Artist name: Name of the artist (if ID3 tag present).
Album name: Name of the album (if ID3 tag present).
Sampling rate and bit rate: Sampling rate and bit rate
of the current MP3 file.
Notes:
On the CR-315DAB, you can also use the CD
receiver’s [DISPLAY] button to display this informa-
tion.
•To display the disc name, press the [DISPLAY] button
while playback is stopped.
If a file or folder name contains a character that cannot
be displayed, it will be displayed as “FILE n” or
“FOLDER n,” “n” being the file or folder number. You
can set the CD receiver so that it displays underscore
characters in place of any undisplayable characters
(see page 37).
1
Press the [YES/MODE] button
repeatedly until the 1FOLDER
indicator appears.
2
Use the Previous and Next
[ ]/[ ] buttons to select the
folder.
You can select any folder that contains
MP3 files.
3
To start playback, press the
[ENTER] or Play/Pause [ ]
button.
Playback will start with the first MP3
file in the specified folder and continue
until all of the MP3 files in that folder
have been played.
/
DISPLAY
YES/MODE
ENTER
1FOLDER indicator
/
Displaying MP3 Information
During playback, press the [DIS-
PLAY] button repeatedly to dis-
play the following MP3
information.
35
Playing CDs—Continued
With memory playback, you can create a playlist of up
to 25 tracks.
Memory playback can be set only when the input source
is set to CD and playback is stopped.
Selecting Other Tracks During Memory Playback
To select other playlist tracks during memory playback,
use the remote controller’s Previous and Next
[ ]/[ ] buttons.
Checking What’s on the Playlist
To check what tracks are on the playlist, with playback
stopped, use the Fast Reverse and Fast Forward
[ ]/[ ] buttons to scroll through the playlist.
Removing Tracks from the Playlist
While memory playback is stopped, press the
[CLEAR] button. Each press removes the last track
from the playlist.
The playlist will be deleted when you cancel memory
playback, select random playback, turn off the CD
receiver, or remove the CD.
Memory Playback
1
Press the [YES/MODE] button
repeatedly until the MEMORY indi-
cator appears.
2
Use the Previous and Next
[ ]/[ ] buttons to select the
first track you want to add to the
playlist, and then press [ENTER].
Repeat this step to add additional tracks
to the playlist.
You can also use the number buttons on
the remote controller to select tracks.
On the CR-515DAB, you can also use
the multi control to add tracks to the
playlist. Turn the multi control to select a
track, and then push it for ENTER.
To select MP3 files for memory
playback:
In Navigation mode, use steps 1–4 on
page 32. In All Folder mode, use steps
1–4 on page 33.
/
YES/MODE
MENU/NO/
CLEAR
ENTER
/
Number buttons
(see page 31)
(These buttons do
nothing during
memory playback)
MEMORY indicator
Track to be added
to the playlist
Total time of playlist
To remove tracks from the playlist:
Press the [CLEAR] button. Each press
removes the last track from the playlist.
Notes:
If the total playing time is more than
99 minutes and 59 seconds, “– –:– –”
is displayed.
•You can add up to 25 tracks to the
playlist. If you try to add more, the
message “Memory Full” appears.
3
To start memory playback, press
the Play [ ] button.
On the CD receiver, press the Play/Pause
[] button to start memory play-
back.
Track currently playing
/
36
Playing CDs—Continued
With random playback, all of the tracks on the disc are
played in random order.
Random playback can be set only when the input source
is set to CD and playback is stopped.
Cancelling Random Playback
•To cancel random playback, press the [SHUFFLE]
button repeatedly until the RANDOM indicator disap-
pears.
Random playback is cancelled when the CD is
removed or the CD receiver is set to Standby.
With repeat playback, you can play an entire CD repeat-
edly, play one track repeatedly, or combine it with mem-
ory playback to play the playlist repeatedly, or random
playback to play all of the tracks on the disc in random
order repeatedly. With an MP3 CD, you can combine
repeat playback with 1-folder playback to play all of the
tracks in a specified folder repeatedly.
Repeat-1 playback can’t be combined with memory
playback, random playback, or 1-Folder playback.
Cancelling Repeat Playback
•To cancel repeat playback, press the [REPEAT] button
repeatedly until both the REPEAT and REPEAT 1
indicators disappear.
Repeat playback is cancelled when the CD is removed
or the CD receiver is set to Standby.
With the MP3 preferences, you can change the way MP3
file information is displayed and the way MP3 CDs are
played.
The MP3 preferences can be set only when playback is
stopped.
Random Playback
1
Press the [YES/MODE/SHUFFLE]
button repeatedly until the RAN-
DOM indicator appears.
2
To start random playback, press
the Play [ ] button.
Repeat Playback
YES/MODE/
SHUFFLE
REPEAT
RANDOM indicator
Track currently playing
Press the [REPEAT] button repeat-
edly until the REPEAT or
REPEAT 1 indicator appears.
Setting MP3 Preferences
1
Press the [MENU/NO] button
repeatedly until “Disc Name?”
appears.
2
Use the Previous and Next
[ ]/[ ] buttons to select the
preference you want to change.
The preferences are explained in the next
column.
REPEAT or REPEAT 1 indicator
/
MENU/NO/
CLEAR
ENTER
37
Playing CDs—Continued
To cancel the procedure at any point, press the
[MENU/NO] button.
Preferences
Below, the name of each preference is followed by its
options in parentheses, with the default option in bold.
Disc Name? (Display/Not Display)
This preference determines whether or not the disc name
is displayed when an MP3 disc is loaded.
File Name? (Scroll/Not Scroll)
This preference determines whether or not the file name
scrolls across the display when an MP3 file is selected.
In Navigation mode (see page 32), the file name scrolls
across the display regardless of this setting.
Folder Name? (Scroll/Not Scroll)
This preference determines whether or not the folder
name scrolls across the display when an MP3 folder is
selected (in All Folder mode).
In Navigation mode (see page 32), the folder name
scrolls across the display regardless of this setting.
Bad Name? (Replace/Not Replace)
This preference determines whether or not file and folder
names that contain undisplayable characters are replaced
with “FILE n” or “FOLDER n,” “n” being the file or
folder number. When set to Not Replace, displayable
characters are displayed and underscore characters are
used in place of any undisplayable characters.
For ID3 tags, underscore characters are used in place of
undisplayable characters regardless of this preference.
ID3 Ver. 1? (Read/Not Read)
This preference determines whether or not version
1.0/1.1 tags are read and displayed. When set to Not
Read, version 1.0/1.1 tags are not displayed.
ID3 Ver. 2? (Read/Not Read)
This preference determines whether or not version
2.2/2.3/2.4 tags are read and displayed. When set to Not
Read, version 2.2/2.3/2.4 ID3 tags are not displayed.
CD Extra? (Audio/MP3)
This preference applies to CD Extra discs and deter-
mines whether music in the audio session or MP3 files in
the data session are played.
Joliet? (Use SVD/ISO9660)
This preference applies to MP3 discs in Joliet format and
determines whether the CD receiver reads the SVD data
or treats the disc as an ISO 9660 disc. Normally, this
preference doesn’t need to be changed.
SVD (Supplementary Volume Descriptor) supports long
file and folder names and characters other than letters
and numbers. Some CD burning software refers to the
Joliet format as “Windows format.
Hide Number? (Disable/Enable)
This preference determines whether or not the numbers
at the beginning of file and folder names are displayed.
When you create an MP3 CD on a personal computer,
you cannot normally determine the playback order of the
files. However, if you number the MP3 files in order,
starting with 01, 02, 03, and so on, they will play in that
order. If you don’t want these numbers to appear on the
display, choose Not Display.
The following table shows a few examples of numbered
file and folder names and how they will appear with the
Display and Not Display options.
Folder Key? (All Folder/Navigation)
This preference determines how the [FOLDER] button
works. When the All Folder option is selected, pressing
the [FOLDER] button once selects All Folder mode and
pressing and holding it for 2 seconds selects Navigation
mode. When the Navigation option is selected, pressing
the [FOLDER] button once selects Navigation mode and
pressing and holding it for 2 seconds selects All Folder
mode.
3
Press [ENTER].
4
Use the Previous and Next
[ ]/[ ] buttons to select the
preference’s options.
5
Press [ENTER].
When the preference has been set,
“Complete” appears on the display.
File/folder name
Trk/Fld Num Option
Display Not Display
01 Pops 01 Pops Pops
10-Rock 10-Rock Rock
16_Jazz 16_Jazz Jazz
21th Century 21th Century 21th Century
05-07-20 Album 05-07-20 Album Album
38
Listening to the Radio
When tuned into a station, the Tuned indicator
appears. When tuned into a stereo FM station, the FM ST
indicator appears as well.
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Adjusting the Antennas
Tuning into FM/AM Radio Stations
YES/MODE
BAND
( TUN/
TUN )
/
AUTO
FM ST
1
Press the [BAND] button repeat-
edly to select AM or FM.
2
Press the [YES/MODE] button
repeatedly to select Auto or Man-
ual.
•Auto Tuning Mode
The AUTO indicator appears and ste-
reo radio reception is possible.
Manual Tuning Mode
The AUTO indicator is not displayed
and radio reception will be in mono.
3
Use the Fast Reverse and Fast For-
ward [ ]/[ ] buttons to tune
into a station.
In Auto tuning mode, once a station is
found, tuning stops automatically.
The American model changes FM fre-
quency in 0.2 MHz steps, 10 kHz steps
for AM. For other models it’s 0.05 MHz
steps for FM and 9 kHz or 10 kHz steps
for AM.
In Manual Tuning mode, the frequency
stops changing when you release the but-
ton. Press the button repeatedly to
change the frequency one step at a time.
AUTO indicator
1
2
Change the direction of the
antenna to achieve the best
reception.
Affix the antenna with a thumbtack. (Do not
push the thumbtack through the antenna.)
Caution: Be careful not to prick your finger!
Adjusting the AM antenna
Adjust the location and position of the AM
antenna while listening to an AM station to
achieve the best reception.
Adjusting and installing the FM antenna
Choose a location for the FM antenna while
listening to an FM station.
39
Listening to the Radio—Continued
Press the remote controller’s [DISPLAY] button repeatedly to display more radio information.
On the CR-315DAB, you can also use the CD receiver’s [DISPLAY] button to display this information.
RDS is only available on European models and only in
areas where RDS broadcasts are available.
What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
within the European Broadcasting Union (EBU) and
many European FM radio stations use it these days.
The CD receiver supports and displays the Program Ser-
vice Name (PS) and Radio Text (RT) types of RDS data.
The RDS indicator appears on the display when the CD
receiver is tuned to an FM station that supports RDS.
Notes:
If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
The message “Waiting...” may appear while the RT
data is being received.
Displaying Radio Information
DISPLAY
AM/FM/DAB
Frequency
*Preset name
* If the selected preset has no name, “No Name” appears
briefly and then the frequency is displayed. See “Nam-
ing Presets” on page 46.
Receiving RDS
Frequency and preset number
Preset name (if preset has no name)
Program Service Name
Radio Text (if available)
Press the [DISPLAY] button repeatedly to dis-
play the following RDS information.
40
Listening to the Radio—Continued
Selecting DAB for the Very First Time
The very first time you select DAB, the Auto Tuning
function automatically scans the DAB Band III and
L-Band for the multiplexes (i.e., stations) available in
your area.
Once the scanning process is complete, the first station
that was detected is selected.
Using the Auto Tuning Function Manually
If a new DAB station is introduced, or you move to a new
area, you can run the Auto Tuning function again.
1 Press the [MENU/NO] button.
2 Use the Previous and Next [ ]/[ ] buttons to
select “Auto Tuning?” and then press [ENTER].
3 Use the Previous and Next [ ]/[ ] buttons to
select Worldwide or U.K., (see “Auto Tuning?” on
page 42), and then press [ENTER] to start the Auto
Tuning function.
The number of stations found and the scanning progress
are shown on the display.
To cancel Auto Tuning, press the [ENTER],
[MENU/NO/CLEAR] or [YES/MODE] button.
On the CR-515DAB, you can also use the front panel
controls.
1 Push the multi control.
2Turn the multi control to select “Auto Tuning?” and
then push it.
3Turn the multi control to select Worldwide or U.K.,
and then push it to start the Auto Tuning function.
To cancel Auto Tuning, push the multi control.
Listening to DAB Digital Radio
Press the [BAND] button repeat-
edly to select DAB.
When tuned into a DAB station, the
Tuned indicator appears and the
DAB indicator as well.
On the front panel, press the [INPUT]
repeatedly to select DAB.
BAND
/
MENU/NO/
CLEAR
ENTER
Station name
Tuned indicator
DAB indicator
41
Listening to the Radio—Continued
Selecting DAB Stations
On the CR-515DAB, you can also use the multi con-
trol to select DAB stations.
On the CR-315DAB, you can also use the Previous
and Next [ ] or [ ] buttons to select DAB sta-
tions.
Once a DAB station has been preset, these front panel
controls will select presets, in Preset mode. To use
them to select DAB stations, select DAB as the input
source, and then press the Stop [ ] button for 3 sec-
onds until “Station Mode” appears on the display.
Displaying DAB Radio Information
Press the remote controller’s [DISPLAY] button repeat-
edly to display more information about the selected
DAB station.
On the CR-515DAB, you can also use the CD receiver’s
[DISPLAY] button to display this information.
1. DLS (Dynamic Label Segment)
When tuned to a station that’s broadcasting DLS text
data, the text will scroll across the display.
2. Program Type
Displays the type of program.
3. Bit Rate and Audio Mode
Displays the station’s bit rate and audio mode (ste-
reo, mono, or joint stereo).
4. Signal Quality
Displays the signal quality.
0–59: Poor reception
60–79: Good reception
80–100: Excellent reception
5. Multiplex Name
Displays the name of the current multiplex.
6. Multiplex Number and Frequency
Displays the number and frequency of the current
multiplex.
Use the Fast Reverse and Fast
Forward [ ]/[ ] buttons to
select the DAB stations.
If a secondary service is available, a
right angle bracket (>) is displayed.
Press [ ] to listen to the secondary
service.
While the secondary service is
selected, a left angle bracket (<) is dis-
played. Press [ ] to return to the pri-
mary service.
When you select a station that you’ve
selected a lot in the past, the letter F
(short for Favorite) is displayed.
If you select a station that cannot be
received properly, a question mark (?)
is displayed.
DISPLAY
( TUN/
TUN )
/
“F”
“?”
(Scroll)
42
Listening to the Radio—Continued
DAB Setup
Use the following functions and settings to set up DAB
digital radio.
Preset Write?
Select this to preset the current DAB station. See “Pre-
setting AM/FM/DAB Stations Manually” on page 44 for
more information.
Tuning Mode?
With this setting, you can sort the available stations
alphabetically, by multiplex, favorites, or active stations.
Use the Previous and Next [ ]/[ ] buttons to
select the following options, and then press [ENTER].
Alphabet (default): Sort stations alphabetically.
Multiplex: Sort stations by multiplex.
Favorite: Sort stations by favorites. The stations you
select the most will appear at the top of the list.
Active St: Sort by active stations. Receivable sta-
tions appear at the top of the list. stations that
cannot be received properly appear at the bottom
of the list.
Trim Station?
With this function, you can delete all of the stations that
cannot be received properly.
Auto Tuning?
This setting determines which DAB bands are scanned
by the Auto Tuning function (see page 40).
UK: Band III (11B–12D).
Worldwide (default): Band III (5A–13F) and
L-Band (LA–LW).
DRC Setting?
With the DRC (Dynamic Range Control) setting, you
can reduce the dynamic range of DAB digital radio so
that you can still hear quiet parts even when listening at
low volume levels—ideal for listening to the radio late at
night when you don’t want to disturb anyone.
Use the Previous and Next [ ]/[ ] buttons to
select the following options, and then press [ENTER].
0 (default): DRC off.
1/2: Small reduction in dynamic range.
1: Large reduction in dynamic range.
Tuning Aid?
With the Tuning Aid, you can adjust the position and
direction of the DAB antenna while monitoring the sig-
nal strength on the display. If the letter “B” appears on
the display, it means the signal strength is Bad. If the
letter “G” appears, it means the signal strength is Good.
To make the letter “G” appear, adjust the antenna to get
the best signal strength.
Use the Previous and Next [ ]/[ ] buttons to
select other multiplexes (Band III: 5A–13F or L-Band:
LA–LW).
1
Press the [MENU/NO] button.
2
Use the Previous and Next
[ ]/[ ] buttons to select the
item you want to set, and then
press [ENTER].
The items are explained below.
/
MENU/NO/
CLEAR
43
Listening to the Radio—Continued
With the Auto Preset function, you can automatically preset all of the FM radio stations available in your area in one
go. Presets make it easy to select your favorite stations and eliminate the need to tune the radio manually each time you
want to change stations. The Auto Preset function does not preset AM radio stations (see page 44).
Note:
Depending on your location, a preset may be stored with
no station and you will hear only noise when you select
it. In this case, delete the preset (see page 48).
On the CR-515DAB, you can also use the front panel
controls.
1 Press the [INPUT] button repeatedly until “FM”
appears.
2 Push the multi control, and then turn it to select
AutoPreset?”
3 Push the multi control. The confirmation message
AutoPreset??” appears.
4To start the Auto Preset function, push the multi con-
trol.
After Storing Presets You Can:
Select them (see page 45)
Name them for easy identification (see page 46)
Copy them (see page 47)
Erase them (see page 48)
Presetting FM Stations Automatically (Auto Preset)
BAND
/
MENU/NO/
CLEAR
ENTER
INPUT
/
Any existing presets will be deleted when the
Auto Preset function is run.
Auto Preset Caution!
1
Press the [BAND] or INPUT
[ ]/[ ] buttons repeatedly until
“FM” appears.
Make sure the FM antenna is positioned
to achieve the best possible reception.
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select
“AutoPreset?”
3
Press [ENTER].
The confirmation message “AutoPre-
set??” appears.
To cancel the Auto Preset function at this
point, press the [MENU/NO] button.
or
4
To start the Auto Preset function,
press [ENTER].
Up to 20 stations can be preset and pre-
sets are stored in frequency order.
44
Listening to the Radio—Continued
With the Preset Write function, you can manually preset individual AM, FM, and DAB radio stations. Presets make it
easy to select your favorite stations and eliminate the need to tune the radio manually each time you want to change
stations. FM stations can also be preset automatically (see page 43).
On the CR-515DAB, you can also use the front panel
controls.
1Tune into the station you want to store as a preset
(see page 38).
2 Push the multi control, and then turn it to select
“PresetWrite?”
3 Push the multi control.
4Turn the multi control to select a preset.
5To store the station, push the multi control.
Note:
If the current FM station supports RDS and PS (Program
Service Name), the station’s name will be displayed
instead of the frequency. (See page 39 for more on
RDS.)
After Storing Presets You Can:
Select them (see page 45)
Name them for easy identification (see page 46)
Copy them (see page 47)
Erase them (see page 48)
Presetting AM/FM/DAB Stations Manually
/
MENU/NO/
CLEAR
ENTER
•You can store up to 40 FM, AM and DAB stations as presets
and this can be any combination. For example, 27 FM and 13
AM or 20 FM, 12 AM and 8 DAB.
Although AM, FM, and DAB presets share the same num-
bers, they’re selected independently. For example, preset #1
will store an AM station when the AM band is selected, and
an FM station when the FM band is selected.
Stations can be stored to presets in any order. For example,
you could store preset #5 first, #1 second, and so on.
About Presets
1
Tune into the station that you want
to store as a preset.
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select “Pre-
set Write?”
3
Press [ENTER].
The preset number flashes.
To cancel the Preset Write function at
this point, press the [MENU/NO] button.
4
Use the Previous and Next [ ]
/[ ] buttons to select a preset.
5
To store the station, press
[ENTER].
If no station has yet been stored to the
selected preset, “Complete” appears and
the station is stored.
If a station has already been stored in the
selected preset, the message “Over-
write?” appears.
To overwrite the previously stored sta-
tion, press the [YES/MODE] button.
To not overwrite the previously stored
station, press the [MENU/NO] button.
If the message “Memory Full” appears,
all 40 presets have been stored and you’ll
need to erase some presets before you can
store any more stations (see page 48).
6
Repeat steps 1 to 5 to preset more radio
stations.
45
Listening to the Radio—Continued
You must store some presets before you can select them
(see pages 43 and 44).
On the CR-515DAB, you can also use the front panel
controls.
1 Use the [INPUT] button to select AM, FM, or DAB.
2To select DAB stations, press the Stop [ ] button for
3 seconds until “Preset Mode” appears on the dis-
play.
3Turn the multi control to select a preset.
On the CR-315DAB, you can also use the front panel
controls.
1 Use the [INPUT] button to select AM, FM, or DAB.
2To select DAB stations, press the Stop [ ] button for
3 seconds until “Preset Mode” appears on the dis-
play.
3 Use the Previous and Next [ ]/[ ] buttons to
select a preset.
Selecting Preset Stations
1
Use the [BAND] or INPUT [ ]/[ ]
buttons to select AM, FM, or DAB.
The preset you selected the last time you
listened to the radio will still be selected.
2
Use the Previous and Next
[ ]/[ ] buttons to select a
preset.
Press the Previous [ ] button to
select the previous preset. Press the Next
[] button to select the next preset.
INPUT
/
( PRESET/
PRESET )
BAND
/
Number
buttons
or
or
You can also use the number but-
tons as shown in the examples
below to select presets.
To select:
Press:
Preset #8
Used to enter numbers over 10.
Preset #10
Preset #22
46
Listening to the Radio—Continued
You can name presets for easy identification. The preset
name may contain of up to eight characters.
On the CR-515DAB, you can also use the front panel
controls.
1 Select the preset you want to name (see page 45).
2 Push the multi control, and then turn it to select
“Name In?”
3 Push the multi control.
4Turn the multi control to select a character, and then
push it.
5 Repeat step 4 to enter up to 8 characters.
Use the remote controller’s [DISPLAY] button to select
the character groups.
Available Characters
Naming Presets
1
Select the preset you want to
name (see page 45).
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select
“Name In?”
3
Press [ENTER].
4
Press the [DISPLAY] button
repeatedly to select one of the fol-
lowing character groups:
•“A” for uppercase letters.
“a” for lowercase letters.
“1” for numbers and symbols.
5
Selecting letters:
Press the number buttons repeatedly
to select the available letters. For
example, press the [2] button repeat-
edly to select: A, B, or C.
Selecting numbers and symbols:
Use the number buttons to select
numbers.
Press the [>10] button repeatedly to
select: (space) . / * - , ! ? & ’ ( )
Press the [0] button repeatedly to
select: 0 or (space)
/
ENTER
MENU/NO
DISPLAY
Number
buttons
Character group
Note:
Not all of the symbols can be entered by
using the number buttons. Use the Previ-
ous and Next [ ] or [ ] buttons to
select from the full range of symbols.
When you’ve selected the charac-
ter you want, press [ENTER], and
then choose the next character.
Editing characters:
To change or delete a character
you’ve already entered, use the
Rewind and Fast Forward
[ ]/[ ] buttons to select it, and
then select another character, or press
the [CLEAR] button to delete it.
Inserting a new character:
To insert a new character, use the
Rewind and Fast Forward
[ ]/[ ] buttons to select the char-
acter immediately after the insertion
point. That character flashes. Use the
Previous and Next [ ] or [ ]
buttons to select “ ,” press
[ENTER], and then select the new
character.
To cancel the Name In function, press the
[MENU/NO] button for 2 seconds.
6
When you’ve finished entering the
name, press the [YES/MODE] but-
ton.
The preset is named and “Complete”
appears on the display.
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9
_ @ ' < > # $ % & * = ; : + - / ( ) ?
! ’ ” , . (space) (insert)
47
Listening to the Radio—Continued
With the Preset Copy function, you can organize your
presets in the order you want. When you copy a preset,
its name is also copied.
On the CR-515DAB, you can also use the front panel
controls.
1 Select the preset you want to copy (see page 45).
2 Push the multi control, and then turn it to select
“PresetCopy?”
3 Push the multi control.
4Turn the multi control to select the destination pre-
set.
5To copy the preset, push the multi control.
Tip:
If you favorite station is stored in preset #5 and you want
to make it preset #1, copy preset #5 to preset #1. To keep
the station that’s already stored in preset #1, you may
want to copy it to an unused preset first.
Copying Presets
1
Select the preset you want to copy
(see page 45).
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select “Pre-
setCopy?”
3
Press [ENTER].
The number of the preset to be copied
flashes.
4
Use the Previous and Next
[ ]/[ ] buttons to select the
destination preset.
The number of the destination preset
flashes.
/
MENU/NO/
CLEAR
ENTER
5
To copy the preset, press
[ENTER].
If no station has yet been stored in the
destination preset, the station is copied
and “Complete” appears.
If a station has already been stored in the
destination preset, the message “Over-
write?” appears.
To overwrite the previously stored sta-
tion, press [ENTER].
To not overwrite the previously stored
station, press the [MENU/NO] button.
48
Listening to the Radio—Continued
On the CR-515DAB, you can also use the front panel
controls.
1 Select the preset whose name you want to erase (see
page 45).
2 Push the multi control, and then turn it to select
“NameErase?”
3To erase the preset’s name, push the multi control.
On the CR-515DAB, you can also use the front panel
controls.
1 Select the preset you want to erase (see page 45).
2 Push the multi control, and then turn the multi con-
trol to select “PresetErase?”
3 Push the multi control. The confirmation message
“Erase OK?” appears.
4To erase the preset, push the multi control.
Erasing a Preset’s Name
1
Select the preset whose name you
want to erase (see page 45).
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select
“NameErase?”
3
To erase the preset’s name, press
the [YES/MODE] button.
The preset’s name is erased and “Com-
plete” appears on the display.
Erasing Presets
1
Select the preset you want to
erase (see page 45).
2
Press the [MENU/NO] button, and
then use the Previous and Next
[ ]/[ ] buttons to select
“PresetErase?”
3
Press [ENTER].
A message requesting confirmation
appears.
To cancel the Preset Erase function at
this point, press the [MENU/NO] button.
4
To erase the preset, press
[ENTER].
The preset is erased and “Complete”
appears on the display.
/
MENU/NO/
CLEAR
ENTER
49
Setting the Clock
The AccuClock function normally uses the FM station with the strongest signal to set the clock. However, if the clock
cannot be set properly using that station, you can specify which FM station the AccuClock function should use. This
must be an FM station that supports RDS CT (Clock Time) information.
Setting AccuClock to Use a Specific Station
1
Press the [TIMER] button.
“Clock” appears on the display.
If the clock has already been set, a timer
option appears instead, in which case
you’ll need to press the [TIMER] button
repeatedly until “Clock” appears.
2
Press [ENTER].
AccuClock”or “*AccuClock*” appears
on the display.
If “Manual Adjust” appears, use the Pre-
vious and Next [ ]/[ ] buttons to
select “AccuClock” or “*AccuClock*”.
3
Press [ENTER].
The frequency flashes on the display.
4
Use the Rewind and Fast Forward
[ ]/[ ] buttons to tune into the
FM station.
Tip:
If you press the [YES/MODE] button
instead of using the Rewind and Fast
Forward [ ]/[ ] buttons, the CD
receiver will automatically search for a
suitable station.
The RDS indicator appears when tuned
into a station that supports RDS.
The RDS indicator will flash while the
CD receiver searches for a station and
light up continuously when a station is
found.
RDS indicator
5
When you’ve selected the station,
press [ENTER].
While the clock is being set, “Wait”
flashes on the display. It may take a few
minutes to set the clock. When the clock
has been set, the message “Clock
Adjusted” scrolls across the display, then
the day and time are displayed for a
while.
Notes:
If the clock is not set correctly, specify
another FM station and try again or set
the clock manually (see page 50).
The AccuClock function automati-
cally updates the clock every day. If
you don’t want it to, you can turn off
the AccuClock function (see page 26).
50
Setting the Clock—Continued
The time can be displayed in either 12- or 24-hour for-
mat.
Displaying the Day and Time
To display the day and time, press the remote controller’s
[CLOCK CALL] button.
If the CD receiver is on Standby, the time is displayed for
8 seconds.
Using the 12- or 24-hour Format
To change the time format between 12-hour and 24-hour,
while the time is shown on the display, press the [DIS-
PLAY] button.
Displaying the Time in Standby Mode
To set the CD receiver so that the time is displayed while
its on Standby, turn on the CD receiver, and then press
and hold its [STANDBY/ON] button for 2 seconds.
Note that having the time displayed in Standby mode
will consume a little more power.
Setting the Clock Manually
1
Press the [TIMER] button repeat-
edly until “Clock” appears.
2
Press [ENTER].
3
Use the Previous and Next [ ]/
[] buttons to select “Manual
Adjust.”.
4
Press [ENTER].
5
Use the Previous and Next [ ]/
[] buttons to select the day of
the week.
You can select: SUN, MON, TUE, WED,
THU, FRI, or SAT.
6
Press [ENTER].
To cancel the Manual Adjust function at
this point, press the [MENU/NO] button.
/
TIMER
STANDBY/ON
ENTER
DISPLAY
MENU/NO/
CLEAR
CLOCK
CALL
Number
button
7
Use the Previous and Next [ ]/
[] buttons to set the time.
You can also use the remote controller’s
number buttons to enter the time.
For the 12-hour format, use the remote
controller’s [>10] button to select AM or
PM.
8
Press [ENTER].
The clock is set and the second dot starts
flashing.
51
Using the Timers
The CD receiver has five timers: four programmable tim-
ers for automated playback or recording, and a sleep timer
for turning the CD receiver off after a specified period.
The timers can be used with other Onkyo components
that are connected to the CD receiver via (see pages
20 to 24 for hookup details).
The various settings for the four programmable timers
are explained here. For details on the sleep timer, see
page 55.
Timer Types
Each timer can be programmed for playback (Play) or
recording (Rec).
Play
Play mode can be used to start playback at a specified
time on the CD receiver or another Onkyo component
that’s connected to the CD receiver with an cable.
You could use a Play timer to turn on the CD receiver
every morning, just like a radio alarm.
Rec
Rec mode can be used to start playback on one compo-
nent and start recording on another component at a spec-
ified time. The recording component (e.g., Onkyo
cassette deck or MD recorder) must be connected to the
CD receiver with an cable. You could use a Rec
timer to record your favorite radio show every day.
Playback and Recording Components
The playback component can be the CD receiver (AM,
FM, DAB or CD), an Onkyo component (MD recorder,
cassette deck, etc) that’s connected to the CD receiver
with an cable, or a component that’s connected to
one of the CD receiver’s inputs, perhaps one with its own
built-in timer.
The recording component can be an Onkyo MD recorder
or cassette deck that’s connected to the CD receiver with
an cable.
Repeat Timers
Each timer can be programmed to work just once
(Once), every week (Every), every day (Every Day), or
on a range of days (Days Set).
Once
The timer will work just once.
Every
The timer will work every week on the specified day and
time.
Everyday
The timer will work every day.
•Days Set
The timer will work on the specified range of days. With
this setting, you could set up a morning alarm for Mon-
day to Friday.
Timer Examples
The following examples highlight some of the ways in
which you can use the timers.
Timer 1: To wake up to your favorite radio station (pre-
set #1) every morning, set as follows:
Play
FM 1EveryEvery DayOn 7:00Off 7:30
If you want a radio alarm only on weekdays, select
“Days Set” instead of “Every Day” and specify
“MON–FRI.
Timer 2: To record a one-off radio show (preset #2) to a
cassette deck this Sunday, set as follows:
Rec
FM 2TAPEOnceSUNOn 21:00Off 22:00
(You need an -capable Onkyo cassette recorder or
MD recorder to do the recording.)
Timer 3: To record an FM radio show to a MiniDisc
recorder every day from Monday to Friday, set as fol-
lows:
Rec
FM 1MDEveryDays SetMONFRIOn
15:00
Off 15:30
Timer Priority
If two or more timers are set to the same On time, the
lowest numbered timer has priority. For example:
Timer 1: 07:00 – 13:00 (This timer has priority.)
Timer 2: 07:00 – 12:30
If two or more timers overlap, the timer with the earliest
start time has priority. For example:
Timer 1: 9:00 – 10:00
Timer 2: 8:00 – 10:00 (This timer has priority.)
If the On and Off times of two timers are the same, the
timer with the earliest start time has priority and the
other timer will fail. For example:
Timer 1: 0:00 – 1:00 (This timer has priority.)
Timer 2: 1:00 – 2:00
Timer Indicators
When a timer has been set, the TIMER indica-
tor and the number of the timer appear on the
display. If the timer has been set to perform
recording, an underscore character appears
underneath the timer’s number.
Notes:
The timers work only if the CD receiver is on Standby.
If it’s on when a timer is supposed to start playback or
recording, nothing will happen.
While timed playback or recording is in progress, the
timer’s Off time cannot be changed.
•To use timed playback or recording with an external
component, make sure it’s properly connected to the
CD receiver. Also, for to work properly, make
sure that the Input Display on the CD receiver is set to
match the type of component you’ve connected to the
MD/TAPE IN, DOCK/CDR IN, or DIGITAL IN (see
page 29).
About the Timers
52
Using the Timers—Continued
Notes:
•You must set the clock before you can program the
timers.
Before programming a timer to turn on the radio, you
must preset the station you want to use. (See pages 43
and 44.)
If you don’t operate any buttons for 60 seconds while
programming a timer, the procedure will be cancelled
and the previous display will reappear.
Programming the Timers
1
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4, and
then press [ENTER].
If “Clock” appears, you need to set the
clock (see page 26).
2
Use the Previous and Next [ ]/
[] buttons to select Play or
Rec, and then press [ENTER].
If you can’t select Rec, make sure that
your Onkyo cassette deck or MD
recorder is properly connected to the
MD/TAPE jacks (pages 20 and 21) and
the Input Display is set accordingly
(page 29).
/
TIMER
STANDBY/ON
ENTER
Number buttons
or
3
Use the Previous and Next [ ]/
[] buttons to select the source,
and then press [ENTER].
You can select the following sources:
CR-515DAB
FM, AM, TAPE, DOCK, LINE1, LINE2,
DIGITAL, CD, or DAB.
CR-315DAB
FM, AM, TAPE, DOCK, LINE, CD, or
DAB.
If you selected Rec, CD cannot be
selected as the source.
4
If you selected AM, FM, or DAB,
use the Previous and Next [ ]/
[] buttons to select the radio
preset, and then press [ENTER].
5
If you selected Rec, make sure the
name of the connected recorder is
flashing on the display, and then
press [ENTER].
You can select TAPE or MD.
6
Use the Previous and Next [ ]/
[] buttons to select Once or
Every, and then press [ENTER].
Select Once for on-off operation. Select
Every to perform the same operation
every week.
53
Using the Timers—Continued
To return to step 1 and start timer programming all over
again, press the [MENU/NO] button at any point in this
procedure.
7
If you selected Once, use the Pre-
vious and Next [ ]/[ ] but-
tons to select the day, and then
press [ENTER].
You can select: SUN, MON, TUE, WED,
THU, FRI, or SAT.
8
If you selected Every, use the Pre-
vious and Next [ ]/[ ] but-
tons to select the day, Everyday, or
Days Set, and then press [ENTER].
You can select the following:
9
If you selected Days Set, use the
Previous and Next [ ]/[ ] but-
tons to select the first day, and
then press [ENTER].
Use the Previous and Next [ ]/
[] buttons again to select the
last day, and then press [ENTER].
You can select only consecutive days.
10
Use the Previous and Next [ ]/
[] buttons to specify the On
time, and then press [ENTER].
You can also use the remote controller’s
number buttons to enter the time. For
example, to enter 7:29, press [>10], [0],
[7], [2], and [9].
Notes:
Once the On time is set, the Off time is
automatically set to one hour later.
•To ensure that the first few seconds of
a program are recorded when using
timer recording, set the On time
slightly ahead of the program’s start
time (about 1 minute).
SUN
TUE
MON
Days Set Everyday
WED THU
SAT
FRI
11
Use the Previous and Next [ ]/
[] buttons to specify the Off
time, and then press [ENTER].
12
Use the Previous and Next [ ]/
[] buttons to specify the CD
receiver’s volume level, and then
press [ENTER].
The default setting is 10.
If you want to use your normal volume
level setting for the timer, press the Pre-
vious [ ] button repeatedly until
“TimerVol.Off” appears on the display.
In this case, the timer will use the volume
level that was set before the CD receiver
was set to Standby.
13
Press the [STANDBY/ON] button
to set the CD receiver to Standby.
Notes:
Be sure to set the CD receiver to
Standby, otherwise the timed opera-
tion will not work.
While a timed operation is in progress,
you can cancel it by pressing the
[TIMER] or [SLEEP] button.
While timed recording is in progress,
the output of the CD receiver is muted.
To hear what’s being recorded, press
the [MUTING] button. Press it again
to mute the CD receiver.
Memory, random, and 1-Folder play-
back cannot be used with the timers.
TIMER indicator
Number of
programmed
timer
Underscore indicates
timer programmed for
recording
54
Using the Timers—Continued
Once a timer has been programmed, you can turn it on or
off as necessary. For example, while you’re on holiday,
you may want to turn off the timer you use as an early-
morning alarm.
Turning Timers On and Off
1
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4.
When a timer has been programmed, its
number appears on the display.
2
Use the Previous and Next [ ]/
[] buttons to select Timer On or
Timer Off.
After a few moments, the previous dis-
play reappears.
/
TIMER
ENTER
MENU/NO/
CLEAR
or
Checking Timer Settings
1
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4, and
then press [ENTER].
2
Press [ENTER] repeatedly to see
all of the timer’s settings.
Notes:
•You can change the settings by using
the Previous and Next [ ]/[ ]
buttons.
If you change the settings of a timer
that is off, that timer will be turned on.
If you don’t change any settings, the pre-
vious display reappears.
To return to the previous display at any
point in this procedure, press the
[MENU/NO] button.
55
Using the Timers—Continued
With the sleep timer, you can set the CD receiver so that
it automatically turns off after a specified period.
Checking the Remaining Sleep Time
To check the remaining sleep time, press the [SLEEP]
button.
Note that if you press the [SLEEP] button while the sleep
time is being displayed, you’ll shorten the sleep time by
10 minutes.
Canceling the Sleep Timer
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
Using the Sleep Timer
Press the [SLEEP] button repeat-
edly to select the required sleep
time.
With the [SLEEP] button, you can set the
sleep time from 90 to 10 minutes in 10
minute increments.
Use the Previous and Next [ ]/[ ]
buttons to set the sleep time in 1 minute
increments from 99 to 1.
When the sleep timer has been set, the
SLEEP indicator appears on the display,
as shown. The sleep time appears on the
display for about 8 seconds, then the pre-
vious display reappears.
Note:
The sleep timer will be ignored while
dubbing a CD to an Onkyo cassette deck
or MD recorder is in progress. The CD
receiver will automatically switch to
Standby when the dubbing is complete.
SLEEP
SLEEP indicator
56
Troubleshooting
If you have any trouble using the CD receiver, look for a solution in this section.
Can’t turn on the CD receiver.
Make sure that the power cord is properly plugged into the wall outlet (see page 25).
Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
The CD receiver turns off unexpectedly.
If the sleep timer has been set and the TIMER indicator is shown on the display, the CD receiver will turn off auto-
matically after a specified period.
When timed playback or recording finishes, the CD receiver automatically switches to Standby mode.
If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can happen if
there’s a short between the positive and negative wires of a speaker cable.
There’s no sound.
Make sure the CD receiver’s volume control is not set to minimum (see page 27).
Make sure the correct input source is selected (see page 27).
Make sure the CD receiver is not muted (see page 28).
Make sure the speakers are connected correctly (see page 18).
Check all connections and correct as necessary (see pages 16 to 25).
While headphones are connected, the speakers output no sound (see page 27).
The sound quality is not good.
Make sure the speaker cables are connected with the correct polarity (see page 18).
Make sure all audio connecting plugs are pushed in all the way (see page 19).
The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices
away from the CD receiver.
If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone that’s being
used to make a call, the CD receiver may output noise.
The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during playback or
when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
Headphone output is intermittent or there’s no sound.
This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for cleaning
information. Also, make sure that the headphones cable is not broken or damaged.
Audio performance
Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time
to warm up.
Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.
Playback jumps.
The CD receiver is being subjected to vibration or the disc is scratched or dirty (see page 15).
If you can’t resolve the issue yourself, try resetting the CD receiver before contacting your Onkyo dealer.
To reset the CD receiver to its factory defaults, turn it on and, while holding down
the [ ] button, press the [STANDBY/ON] button. “Clear” will appear on the display
and the CD receiver will enter Standby mode.
Note that resetting the CD receiver will delete your radio presets and custom settings.
Power
Audio
CD Playback
57
Troubleshooting—Continued
Can’t add tracks to the playlist for memory playback.
Make sure there’s a disc in the CD receiver. Also, you can only add valid track numbers. For example, if the CD
contains 11 tracks, you cannot add track #12.
The disc will not play.
Make sure the disc has been loaded correctly, with the label-side facing up.
Check to see if the surface of the disc is dirty (see page 15).
If condensation is suspected, turn on the CD receiver and leave it for 1 hour before playing any discs.
Some CD-R/RW discs may not be playable (see page 14).
It takes a long time for playback to start.
It may take the CD receiver a while to read CDs that contain many tracks or files.
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all stations, or
the ST indicator doesn’t light up when tuned to a stereo FM station.
Check the antenna connections (see page 16).
Change the position of the antenna (see page 38).
•Move the CD receiver away from a nearby TV or computer.
Cars or airplanes can cause noisy interference.
The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
•Try setting FM mode to mono (see page 38).
•Move power cords and speaker cables as far away as possible from the tuner’s antenna.
When listening to an AM station, noise may be heard when you operate the remote controller.
If none of the above improves the reception, install an outdoor antenna (see page 17).
If a power outage occurs or the power cable is disconnected:
If the preset stations are lost, preset them again (see pages 43, 44).
The clock and timer settings will be lost. Set the clock and timers again (see pages 49, 50).
Can’t adjust the frequency of the radio.
Use the Fast Reverse and Fast Forward [ ]/[ ] buttons to change the frequency of the radio (see page 38).
RDS doesn’t work.
The FM station you are tuned to doesn’t support RDS.
Install an outdoor FM antenna (see page 17).
Change the position or direction of your outdoor FM antenna (see pages 17, 38).
•Move the FM antenna as far away as possible from fluorescent lights (see page 38).
The remote controller doesn’t work properly.
Make sure the batteries have been installed with the correct polarity (+/–) (see page 5).
Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)
The remote controller is too far away from the CD receiver, or there’s an obstacle between them (see page 5).
The CD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
The CD receiver is located behind the glass doors of a audio rack or cabinet.
Interactive control with other Onkyo -capable components is not working.
Make sure the cables and analog audio cables are connected correctly (see pages 19 to 25). Connecting only an
cable won’t work.
Make sure the Input Display matches the type of device that you’ve connected to the CD receiver (see page 29).
When recording an MP3 CD to an Onkyo recording component, recording will start without performing a peak search
when the [CD DUBBING] button is pressed on the recording component. This is not a malfunction.
Tuner
Remote Controller
External Components
58
Troubleshooting—Continued
No sound is heard from a connected component.
Make sure the optical digital audio cable is not bent or damaged.
On the external component, set the digital output format to PCM, as the CD receiver supports only PCM signals.
No sound is heard from your turntable.
Make sure the turntable has a built-in phono equalizer.
If the turntable doesn’t have a phono equalizer built-in, you must provide one.
Timer playback or recording doesn’t work.
Make sure the clock has been set correctly (see page 49).
•Timed operation will fail if the CD receiver is on at the specified On time, so make sure it’s set to Standby (see
page 53).
The timer may overlap with another timer. If you program several timers, make sure they don’t overlap (see page 51).
If you press the [SLEEP] or [TIMER] button while a timed operation is in progress, the timer will be cancelled.
Make sure the cables and analog audio cables are connected correctly (see pages 19 to 25).
If you’re using an Onkyo component for timed playback or recording, you must set the Input Display to match that
component (see page 29).
The time is not displayed in Standby mode.
Set the CD receiver so that the time is displayed in Standby mode (see page 50).
Timers
Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure that the material will be recorded correctly.
The CD receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this
should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.
59
Specifications
Specifications and features are subject to change without notice.
General
CR-515DAB CR-315DAB
Power Supply: AC 230 V, 50 Hz AC 230 V, 50 Hz
Power Consumption: 56 W 56 W
Stand-by Power Consumption: 0.25 W 0.25 W
Dimensions (W
× H × D):
205
×
116
×
353 mm (8-1/16"
×
4-9/16"
×
13-7/8") 205
×
116
×
352.5 mm (8-1/16"
×
4-9/16"
×
13-7/8")
Weight: 4.3 kg (9.5 lbs.) 4.2 kg (9.3 lbs.)
Audio Inputs
Digital Inputs: 1 (optical) 0
Analog Inputs: 4 (LINE1, LINE2, DOCK, TAPE) 3 (LINE, DOCK, TAPE)
Audio Outputs
Analog Outputs: 2 (DOCK, TAPE) 1 (TAPE)
Subwoofer Pre Outputs: 1 1
Speaker Outputs: 2 2
Phones: 1 1
Amplifier Section
CR-515DAB CR-315DAB
Power Output: 26 W + 26 W (4, 1 kHz, 10% THD)
2ch
×
20 W (4, 1 kHz, 2ch driven, IEC)
25 W + 25 W (4, 1 kHz, 10% THD)
2ch
×
19 W (4, 1 kHz, 2ch driven, IEC)
THD (Total Harmonic Distortion): 0.4% (1 kHz, 1 W) 0.9% (Power Rated) 0.4% (1 kHz, 1 W)
Damping Factor: 25 (Front, 1 kHz, 8 ) 25 (Front, 1 kHz, 8 )
Input Sensitivity and Impedance: 150 mV/50 k (TAPE) 150 mV/50 k (TAPE)
Output Level and Impedance: 150 mV/2.2 (REC OUT) 150 mV/2.2 (REC OUT)
Frequency Response: 10 Hz–100 kHz/±3 dB (TAPE) 10 Hz–100 kHz/±3 dB (TAPE)
Tone Control: ±6 dB, 80 Hz (BASS)
±8 dB, 10 kHz (TREBLE)
+7 dB, 80 Hz (S.BASS)
±6 dB, 80 Hz (BASS)
±8 dB, 10 kHz (TREBLE)
+7 dB, 80 Hz (S.BASS)
Signal to Noise Ratio: 100 dB (LINE, IHF-A) 100 dB (LINE, IHF-A)
Speaker Impedance: 4 –16 4 –16
Tuner Section
CR-515DAB CR-315DAB
FM
Tuning Frequency Range: 87.5 MHz–108.0 MHz 87.5 MHz–108.0 MHz
Usable Sensitivity: Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF) Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF)
Signal to Noise Ratio: Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A) Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A)
THD (Total Harmonic Distortion): Stereo: 0.5% (1 kHz) Mono: 0.3% (1 kHz) Stereo: 0.5% (1 kHz) Mono: 0.3% (1 kHz)
Stereo Separation: 40 dB (1 kHz) 40 dB (1 kHz)
AM
Tuning Frequency Range: 522 kHz–1611 kHz 522 kHz–1611 kHz
Usable Sensitivity: 300 dBf (30 µV) 300 dBf (30 µV)
Signal to Noise Ratio: 40 dB 40 dB
THD (Total Harmonic Distortion): 0.7% 0.7%
DAB
Tuning Frequency Range: 174.928–239.200 MHz 174.928–239.200 MHz
Frequency Response: 20 Hz–20 kHz 20 Hz–20 kHz
Signal to Noise Ratio: 94 dB 94 dB
THD (Total Harmonic Distortion): 0.09% 0.09%
CD
CR-515DAB CR-315DAB
Frequency Response: 4 Hz–20 kHz 10 Hz–20 kHz
Audio Dynamic Range: 96 dB 95 dB
THD (Total Harmonic Distortion): 0.005% 0.007%
Wow and Flutter: Below threshold of measurability Below threshold of measurability
Audio Output/Impedance (Analog): 1.3 V/1.0 k 1.3 V/1.0 k
60
SN 29344262
I0606-1
(C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved.
http://www.onkyo.com/
HOMEPAGE
* 2 9 3 4 4 2 6 2 *
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo CR-515 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo CR-515

Onkyo CR-515 Bedienungsanleitung - Schwedisch - 176 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info