Bedienungsanleitung Onkyo CR-N755 (Seite 35 von 48) (Englisch)

492677

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Custom Setup

The common setting for each input selector is explained

below. Go through the following steps for setup.

Tip:

• You can also use the [MENU/ENTER] jog dial on the

CD receiver.

Preferences

ASb (Auto Standby)

When “Auto Standby” is set to “On”, the CD receiver

will automatically enter standby mode if there is no

operation for 30 minutes with no audio signal input.

The ASb indicator lights up when the Auto Standby

function is enabled.

Default setting: On (European models), Off (Other

models)

Update

These settings allow you to update the CD receiver’s

firmware. Do not shutdown the power of the CD receiver

while updating.

Note:

• Refer to “Firmware Update” for update procedure (see

page 37).

SleepCharge

You can specify how the power is fed to your USB

device (mobile device) when the CD receiver is in

standby mode.

Note:

• When the “SleepCharge” setting is set to “On”, the

power consumption slightly increases in standby

mode.

• If the iPod/iPhone completely runs out of battery,

charging might not work. In that case you need to turn

the power on again.

• If you disconnect the USB device while

“ReadyCharging” appears, the CD receiver does not

enter the standby mode. Press the On/Standby [8]

button to enter the standby mode again.

• Only the USB port (front) can be used for charging.

Sel Change

When you connect an Onkyo u-capable component,

it’s important that you select the input source name that

matches the type of component for u to work properly.

Before operating this setting, you need to select the input

source that you want to set.

LINE1, LINE2, OPTICAL, COAXIAL

DOCK

Note:

• “DOCK” can be selected for the “LINE1”, “LINE2”,

“OPTICAL”, “COAXIAL” input selector, but not at

the same time.

M.OPT (Music Optimizer)

The Music Optimizer function enhances the sound

quality of compressed music files. When set to “On”, the

M.OPT indicator lights on the CD receiver’s display.

Note:

• This setting can be used only for the NET and USB

input selectors.

• The Music Optimizer function only works with digital

audio input signals with a sampling rate below

48 kHz.

Setting Common Preferences

Press the [MENU] button, and then use the

Arrow [!]/["] buttons to select the

preference you want to change.

Press [ENTER].

Use the Arrow [#]/[$] buttons to select the

preference’s options.

Press [ENTER].

Off

Version

Displays the current version of the firmware.

Update Notice

Enable (default)

Disable

When this setting is enabled, you will be notified if a

firmware update via network is available.

CR via NET: Performs the firmware update via

Internet. Check the network

connection before updating.

CR via USB: Performs the firmware update from a

USB flash drive.

On:

(default)

If you connect USB device (mobile

device), charging will start.

“Charging” appears on the display.

Off: Your USB device (mobile device)

is not charged.

Off (default)

→

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo CR-N755 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo CR-N755

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info