Bedienungsanleitung Onkyo CR-N755 (Seite 38 von 48) (Englisch)

492677

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Firmware Update—Continued

Update Procedure Troubleshooting

Case 1:

If an error occurs, “Error!! *-**” is displayed on the CD

receiver’s display. (Alpha-numeric characters on the

front display are denoted by asterisks.) Refer to the

following table and take appropriate action.

■ Errors during an update via network

Case 2:

If an error occurs during the update process, disconnect

then reconnect the AC power cord and try again.

Case 3:

If you do not have an Internet connection to the network,

please contact Onkyo Support (see page 40).

Press the [MENU] button, and then use the

Arrow [!]/["] buttons to select “Update”.

Press [ENTER].

Note that the message “Not Available” appears and

“Update” option cannot be selected for a short while

after the CD receiver is turned on. Please wait until

it becomes operable.

Use the Arrow [#]/[$] buttons to select “CR

via NET” and then press [ENTER].

Note that this option will not be available if there is

no firmware file newer than the currently installed

version.

Select “UpdateStart” and press [ENTER].

The update process will begin.

The message “Completed” appears on the

CD receiver’s display, indicating that the

update has been completed.

Press the [8ON/STANDBY] button on the

front panel. The CD receiver will enter

standby mode.

Do not use On/Standby [8] button on the remote

controller.

The CD receiver will enter standby mode

automatically in 3 minutes regardless of whether the

[8ON/STANDBY] button is pressed.

Congratulations! You now have the latest firmware

installed on your Onkyo CD receiver.

Error Code Description

-10,

-20

The Ethernet cable was not detected.

Reconnect the cable properly.

-11,

-13,

-21,

-28

Internet connection error.

Check the following items:

• Make sure the IP address, subnet

mask, gateway address, and DNS

server are configured properly.

• Make sure the router is turned on.

• Make sure the CD receiver and the

router are connected with an

Ethernet cable.

• Make sure your router is configured

properly. See the instruction manual

of the router.

• If your network allows only one

client connection and there is any

other device already connected, the

CD receiver will not be able to

access the network. Consult your

Internet Service Provider (ISP).

• If your modem does not function as

a router, you will need a router.

Depending on your network, you

may need to configure the proxy

server if necessary. See the

document provided by your ISP. If

you are still unable to access the

Internet, the DNS or proxy server

may be temporarily down. Contact

your ISP.

Others

Retry the update procedure from the

beginning. If the error persists, please

contact Onkyo Support (see page 40)

and provide the error code.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo CR-N755 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo CR-N755

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info