Bedienungsanleitung Onkyo CS-245BT (Seite 22 von 36) (Englisch)

549883

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Playing Back via Bluetooth

Note:

• If your mobile phone supports A2DP protocol, its

music will play through the CD receiver.

• You can build a Bluetooth connection with a mobile

phone, an iPod or any other Bluetooth-enabled

devices.

Press the [INPUT] button on the top panel

repeatedly to select the “Bluetooth” input.

Tip:

• Alternatively, you can use the remote controller’s

[ /LINE] button.

Press the [ Bluetooth PAIRING] button on

the top panel. to put the CD receiver into the

pairing mode.

“Pairing...” appears on the CD receiver’s display.

If you hold the [ Bluetooth PAIRING] button for

more than 2 seconds during the process of pairing,

the operation will be cancelled.

During this period, you can operate the

mobile phone, iPod or Bluetooth-enabled

device to pair with the CD receiver within a

10m range.

For details on the Bluetooth connection, refer to the

user manual of the Bluetooth-enabled device.

The CD receiver may not work as normal

depending on the circumstance even though the CD

receiver is placed within the 10 m range. In such

cases, get the Bluetooth-enabled device closer to

the CD receiver and retry the operation.

Once the CD receiver is detected and its

name “Onkyo CR-245BT” appears on the

display of your Bluetooth-enabled device,

select the “Onkyo CR-245BT.” If a prompt

requests a password, key in the “0000”.

When a Bluetooth connection is established

successfully, the “ ” indicator will be solid on

and “Bluetooth” appears on the display of the CD

receiver.

Select the desired music and press “1/3”

button on your device. The CD receiver

automatically starts playing the audio.

If the “ ” indicator is not lit and “Bluetooth”

appears on the display of the CD receiver after 2

minutes have elapsed after “Pairing...” appears, this

means that the pairing is not done successfully.

Perform the above procedure 1 to 4 again.

Note:

• If there is no sound output even after the paring is done

successfully, consult the user manual of the Bluetooth-

enabled device, and then select the

“Onkyo CR-245BT” as the audio output device.

• The CD receiver can store the pairing information of

up to 8 Bluetooth devices. If the pairing is done for the

ninth Bluetooth device, the pairing information of

device connected via Bluetooth in the most past times

is erased.

• The multiple Bluetooth devices cannot be connected

at the same time.

If you press the [DISPLAY] button during the Bluetooth

connection, the following Bluetooth information

appears.

The information is shown in the following order.

• Audio CODEC

• Sampling frequency

With Bluetooth Standby, you can set the CD receiver so

that it will be automatically turned on if the Bluetooth

device is operated while the CD receiver is on standby.

The default setting is “Off”.

Make settings for this function while CD receiver is in

standby mode.

Press and hold the [8 ON/STANDBY] button on

the CD receiver while it is on standby (about 3

seconds).

The SLEEP indicator will be dimly-lit.

Note:

• To switch between “On” and “Off” , repeat this

procedure.

Listening to an audio from Bluetooth

device

Displaying Bluetooth Information

Setting Bluetooth Standby

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo CS-245BT Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo CS-245BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info