138965
59
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
59
4
5
6
7
Press and hold down the button on
the other remote control unit that
corresponds to the command you
want to program until the SEND/
LEARN indicator flashes twice to
indicate that the command has
been successfully programmed.
After flashing twice, the SEND/LEARN indicator
lights up again.
Repeat steps 3 and 4 to program
other commands within the same
mode.
Repeat step 2 to 4 to program
commands to the other mode.
Press the MODE button (DVD or
RECVR) that you pressed in step 2
to complete the programming.
Use the remote controller to
perform the newly learned
command to confirm that it was
learned correctly.
Notes
Some buttons have already been programmed to control functions of an
Onkyo receiver. Therefore, it is recommended to program additional
functions of the receiver that are not already programmed in the remote
controller.
If no buttons are pressed for more than 30 seconds during the
programming, or if you perform an invalid operation, the SEND/LEARN
indicator flashes three times quickly and the remote controller exits the
programming mode. Resume programming from step 2.
If you perform an invalid operation during programming, the SEND/
LEARN indicator flashes three times quickly and the remote controller
exits the programming mode. Resume from Step 2.
When you want to program a command to a button to which you have
already programmed a command, simply follow the same procedure and
programming for that button will be overwritten.
The remote controller uses infrared rays to send its commands, as do most
other remote control units. Though most remote control units can be
memorized by the remote controller, be aware that some remote control
units use a system that is quite different from the remote controller and
therefore may not be able to be programmed.
Some remote control units have a single button that performs multiple
functions (for example, the function may change each time the button is
pressed). If this is the case, each function must be programmed to a
separate button on the remote controller.
Once you have programmed the commands from the other remote control
unit, refer to the instructions supplied with the other component to operate.
Make sure that both the remote controller and the other remote control unit
have new batteries. If either of them has batteries that are low, you may not
be able to program the commands of the other remote control unit properly
into the remote controller.
After programming another function to the ZOOM ON button or ZOOM
+/– buttons, it is no longer possible to perform the Zoom function. To use
the Zoom function again, it is necessary to erase the commands
programmed to those buttons. For details, see page 60.
Removing the batteries from the remote controller for at least 10 minutes
erases all of the commands that have been programmed in the remote
controller.
DV-S939(US_E)p56-60.p65 10/2/00, 3:26 PM59
59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo dv s 939 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info