136557
41
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
41
Connecting
—Continued
Connect the IR receiver to the DV-SP1000/
DV-SP1000E as shown below.
Controlling Other Out-of-range
Components
For another component that is out of range of its remote
controller, you can use a commercially available IR
emitter to retransmit the remote controller signals
received at the DV-SP1000/DV-SP1000E’s IR IN, as
shown below.
Connect the IR emitter to the DV-SP1000/
DV-SP1000E’s IR OUT, and place the IR emitter in front
of the other AV component’s remote control sensor (usu-
ally located on its front panel), as shown below. See the
instructions supplied with the IR emitter.
Only remote controller signals received by the
DV-SP1000/DV-SP1000E’s IR IN are fed through to the
IR OUT. Signals picked up by the DV-SP1000/
DV-SP1000E’s remote control sensor are not.
Notes:
Before connecting the power cord, complete all of the
necessary audio and video connections.
Do not use a power cord other than the one supplied
with the DV-SP1000/DV-SP1000E, which is designed
exclusively for use with the DV-SP1000/
DV-SP1000E and should not be used with any other
component.
•Never disconnect the power cord from the
DV-SP1000/DV-SP1000E while the other end is still
plugged into a wall outlet. Doing so may cause an
electric shock. Always disconnect the power cord
from the wall outlet first.
The DV-SP1000/DV-SP1000E (not the Canadian
model) is shipped with the POWER switch in the ON
position ( ). When the power cord is connected for
the very first time, the DV-SP1000/DV-SP1000E will
go on standby and the STANDBY indicator will light
up.
•To completely shutdown the DV-SP1000/
DV-SP1000E, set the POWER switch to the OFF posi-
tion ( ). (This does not apply to the Canadian model).
OUT
IN
IR
DV-SP1000/DV-SP1000E
from connecting block
Miniplug cable
Signal flow
IR IN
IR OUT
Connecting
block
IR receiver
DV-SP1000/
DV-SP1000E
IR emitter
Remote controller
Other
component
Signal flow
OUT
IN
IR
Signal flow
DV-SP1000/
DV-SP1000E
Remote control
Other component
sensor
from connecting block
Miniplug cable
Miniplug
IR emitter
IR Emitter
Connecting the Power Cord
1
Plug the supplied power cord into the
DV-SP1000/DV-SP1000E’s AC INLET.
2
Plug the other end of the power cord into
a suitable AC wall outlet.
The STANDBY indicator lights up.
The STANDBY indicator comes on only if the
POWER switch is in the ON ( ) position. (This
does not apply to the Canadian model).
M
ODEL NO.
DPC
-
7.4
DVD
CHANGER
AC
INLET
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo dv sp 1000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo dv sp 1000

Onkyo dv sp 1000 Bedienungsanleitung - Französisch, Spanisch - 192 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info