Bedienungsanleitung Onkyo dv sp 500 (Seite 58 von 60) (Englisch)

136909

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Causes

• The Setup screen Audio menu [96 kHz

PCM Out] setting is set to [96 kHz].

• The Setup screen Audio menu [Digital

Out] is set to [Off].

• A wrong sound signal conversion method

is selected.

• The pause mode is engaged.

• The volume level of TV or amplifier is set

to minimum.

• The DVD or CD is recorded in DTS audio.

• The multi aspect setting is not

appropriate.

• The TV is connected with an S-video

cord.

• The track name does not end in “.mp3” or

“.MP3”.

• More than 251 folders and tracks are

recorded on a disc.

• A multi-session disc is inserted.

• No batteries are inserted in the remote

controller.

• The batteries are worn out.

• The remote controller is not pointed at the

remote sensor of the DVD Player.

• The remote controller is too far from the

DVD Player

Remedies

• Either connect using the analog outputs,

or set [96kHz PCM Out] in the Audio

menu to [96kHz 3 48 kHz].

• Set [Digital Out] to [On].

• Check the current sound signal

conversion method, and select the right

setting.

• Press 3 or 8 to exit the pause mode.

• Increase the volume level.

• DTS audio is only output from the digital

output jacks. Connect the digital output on

the player to the digital input on a receiver

or amplifier with a built in DTS decoder to

hear DTS audio.

• Change the aspect setting in the [TV

Screen] setting in the Setup screen Video

1 menu to the screen type most

appropriate to the TV or monitor you are

using.

• If you connected your TV with an S-Video

cord, in rare cases the TV picture may

appear stretched. In this case switch the

output from [S2] to [S1]

• This system will not recognize file that

does not end in ".mp3" or ".MP3" as an

MP3 track. Change the track name.

• This player only recognizes the first 250

folders and tracks on a disc. If there are

more folders/tracks than this, you will not

be able to play them.

• This player is not compatible with multi-

session discs. If the disc is multi-session,

you will only be able to play tracks

recorded onto the first session.

• Insert new batteries.

• Replace with new batteries.

• Point the remote controller at the remote

sensor of the DVD Player.

• Operate the remote controller within 5 m

Symptoms

No sound is reproduced.

The screen is stretched or

aspect does not change.

Some MP3 tracks appear

to be missing from a disc.

The buttons on the DVD

Player operates but the

buttons on the remote

controller do not operate.

Pages

40, 41

–

DVD Player

Remote Controller

Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static

electricity. If this happens, press the POWER switch on the unit and then press it again after about five seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo dv sp 500 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info