Bedienungsanleitung Onkyo dv sp 501 (Seite 19 von 60) (Englisch)

136788

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Connecting the DV-SP501

—Continued

The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In

this setup, stereo audio is played through the speakers in your TV.

• This player is equipped with copy protection technol-

ogy. Do not connect this player to your TV via a VCR

using AV cables, as the picture from this player will

not appear properly on your TV. (This player may also

not be compatible with some combination TV/VCRs

for the same reason; refer to the manufacturer for more

information.)

• If your TV only has a mono audio input, connect it to

the DV-SP501’s MONO ANALOG AUDIO OUT-

PUT.

Other than European model

• When connecting to your TV as shown above, do not

set the “Component Out” setting (page 45) to “Pro-

gressive.” (Other than European models.)

1. Connect the VIDEO OUTPUT and AUDIO OUT-

PUT ANALOG L/R jacks to a set of A/V inputs

on your TV.

Use the supplied audio/video cable, connecting the

red and white plugs to the audio outputs and the yel-

low plug to the video output. Make sure you match

up the left and right audio outputs with their corre-

sponding inputs for correct stereo sound.

See the following page if you want to use a compo-

nent or S-Video cable for the video connection.

2. Connect the supplied AC power cord to the AC

INLET, then plug into a power outlet.

Notes:

• Before unplugging the player from the power outlet,

make sure you ﬁrst switch it into standby using either

the front panel STANDBY/ON button, or the remote

controller, and wait of the “GOOD BYE” message to

disappear from the player’s display.

•For the above reasons, do not plug this player into a

switched power supply found on some ampliﬁers and

AV receivers.

Other than North American model and European

models

• When TV System is set to “AUTO” or “NTSC”, and

playing an NTSC disc only: When “Component Out”

(page 45) is set to “Progressive”, there is no video out-

put from the “VIDEO OUTPUT” (composite) and

“S VIDEO” jacks. If you want to display video on

more than one monitor simultaneously, make sure that

it is set to Interlace. Switch the player to standby then,

using the front panel controls, press STANDBY/ON

while pressing to switch the player back to

“Interlace.”

North American model

• When “Component Out” (page 45) is set to “Progres-

sive”, there is no video output from the “VIDEO

OUTPUT” (composite) and “S VIDEO” jacks. If you

want to display video on more than one monitor simul-

taneously, make sure that it is set to Interlace. Switch

the player to standby then, using the front panel con-

trols, press STANDBY/ON while pressing to

switch the player back to “Interlace.”

Basic Setup

INLET

COMPONENT

VIDEO

REMOTE

CONTROL

MONO

DIGITAL

OPTICAL COAXIAL

AUDIO

OUTPUT

AUDIO

OUTPUT

ANALOG

VIDEO

OUTPUT

DVD

PLAYER

MODEL NO. DV

501

ANALOG

INPUT

VIDEO IN

To power outlet

DV-SP501_En.book Page 19 Tuesday, May 20, 2003 4:17 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo dv sp 501 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info