Bedienungsanleitung Onkyo HT-R508 (Seite 63 von 64) (Englisch)

463986

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Troubleshooting

—Continued

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 14).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 14).

• Make sure you’ve selected the correct remote control-

ler mode (page 10).

• Make sure you’ve entered the correct remote control

code (page 58).

Can’t control other components

• Make sure you’ve selected the correct remote control-

ler mode (page 10).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, or RI Dock to the TAPE

IN/OUT jacks or CBL/SAT jacks, for the remote con-

troller to work properly, you must set the Input Dis-

play to MD, CDR, or DOCK (page 37).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

•With some AV components, certain buttons may not

work as expected, and some may not work at all.

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver. Be

sure to enter the appropriate remote control code ﬁrst

(page 58).

•To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point

the remote controller at the component. Be sure to

enter the appropriate remote control code ﬁrst

(page 58).

Can’t record

• On your recorder, make sure the correct input is

selected.

•To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., TAPE IN to TAPE OUT, or

VCR/DVR IN to VCR/DVR OUT).

• When the Pure Audio listening mode is selected,

recording is not possible because no video signals are

output. Select another listening mode.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio.

The display doesn’t work

• The display is turned off when the Pure Audio listen-

ing mode is selected.

How do I change the language of a multiplex

source

• Use the “Multiplex” setting on the “Audio Adjust”

menu to select Main or Sub (page 50).

The functions don’t work

•To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected digi-

tally (page 31).

During automatic speaker setup, measurement

fails and the message “Noise Error!” appears

• This can be caused by a speaker malfunction. Make

sure all of your speakers are working properly.

Remote Controller

Recording

Others

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situa-

tions, severe interference, noise from an external

source, or static electricity may cause it to lockup. In the

unlikely event that this happens, unplug the power cord

from the wall outlet, wait at least ﬁve seconds, and then

plug it back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Memory Backup

The AV receiver uses a battery-less memory backup

system in order to retain radio presets and other set-

tings when it’s unplugged or in the case of a power fail-

ure. Although no batteries are required, the AV receiver

must be plugged into an AC outlet in order to charge the

backup system. Once it has been charged, the AV

receiver will retain the settings for several weeks,

although this depends on the environment and will be

shorter in humid climates.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R508 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R508

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info