492666
54
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
Controlling Other Components
En-54
Controlling Other Onkyo
Components
You can use the AV receiver’s remote controller to control
your other Onkyo AV components. This section explains
how to enter the remote control code for a component that
you want to control: DVD, CD, etc.
The following REMOTE MODE butttons are
preprogrammed with remote control codes for controlling
the components listed. You do not need to enter a remote
control code to control these components.
For details on controlling these components, see the
indicated pages.
You’ll need to enter a code for each component that you
want to control.
Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
Preprogrammed Remote Control
Codes
BD/DVD Onkyo Blu-ray Disc player ( page 56)
TV/CD Onkyo CD player ( page 57)
Entering Remote Control Codes
1
Look up the appropriate remote control code in the
Remote Control Codes for Onkyo Components
Connected via u.
2
While holding down the REMOTE MODE button to
which you want to assign a code, press and hold
down DISPLAY (about 3 seconds).
The remote indicator lights.
Note
Remote control codes cannot be entered for RECEIVER.
Except for RECEIVER remote control codes from any
category can be assigned to the REMOTE MODE button.
However, these buttons also work as input selector buttons
( page 20), so choose a REMOTE MODE button that
corresponds with the input to which you connect your
component. For example, if you connect your CD player to
the CD input, choose TV/CD when entering its remote
control code.
3
Within 30 seconds, use the number buttons to enter
the 5-digit remote control code.
The remote indicator flashes twice.
If the remote control code is not entered successfully,
the remote indicator will flash once slowly.
Remote Control Codes for Onkyo
Components Connected via u
1
Make sure the Onkyo component is connected with
an u cable and an analog audio cable (RCA).
See “Connecting Onkyo u Components” for details
( page 17).
2
Enter the appropriate remote control code for a
REMOTE MODE button, by referring to the
previous section.
` 42157:
Onkyo cassette tape deck with u
` 81993:
Onkyo Dock with u
3
Press the REMOTE MODE button, point the
remote controller at the AV receiver, and operate
the component.
To be continued
54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

onkyo-ht-r558

Suche zurücksetzen

  • computer als eingabegerät an den av receiver anschließen
    Eingereicht am 5-8-2021 15:41

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo HT-R558 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo HT-R558

Onkyo HT-R558 Bedienungsanleitung - Deutsch - 80 seiten

Onkyo HT-R558 Bedienungsanleitung - Holländisch - 80 seiten

Onkyo HT-R558 Bedienungsanleitung - Französisch - 80 seiten

Onkyo HT-R558 Bedienungsanleitung - Italienisch - 80 seiten

Onkyo HT-R558 Bedienungsanleitung - Spanisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info