Bedienungsanleitung Onkyo HT-R990 (Seite 54 von 172) (Englisch, Französisch)

462101

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

OSD Setup

■ On Screen Display

` On

` Off

This preference determines whether operation details are

displayed on-screen when an AV receiver function is

adjusted.

Even when “On” is selected, operation details may not be

output if the input source is connected to an HDMI IN.

■ Language

(North American models)

` English

, Deutsch, Français, Español, Italiano,

Nederlands, Svenska

(European models)

` English

, Deutsch, Français, Español, Italiano,

Nederlands, Svenska, 中文

This setting determines the language used for the on-

screen setup menus.

Main menu Hardware Setup

Remote ID

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the remote controller’s ID

Tuner

For AM/FM tuning to work properly, you must specify the

AM/FM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

■ AM/FM Frequency Step (North American

models)

` 10kHz/200kHz

` 9kHz/50kHz:

Select the frequency step according to your area.

■ AM Frequency Step (European models)

` 10kHz:

` 9kHz

Select the frequency step according to your area.

HDMI

■ HDMI Control(RIHD)

` Off

` On

Turn this setting on to allow

p-compatible

components connected via HDMI to be controlled by the

AV receiver (➔ page 82).

Note

• When the setting is set to “On” and the menu is closed, the

names of connected p-compatible components and

“RIHD On” are displayed on the AV receiver.

“Search…” → “(name)” → “RIHD On”

When the AV receiver cannot receive the name of the

component, it is displayed as “Player

” or “Recorder

”, etc (“

”

shows up and indicates the number of components, when two or

more are received).

•When an p-compatible component is connected to the

AV receiver via an HDMI cable, the name of the connected

component is displayed on the AV receiver display. For

example, while you are watching TV broadcasting, if you

operate a Blu-ray Disc/DVD player (being powered on) with the

remote control of the AV receiver, the name of the Blu-ray

Disc/DVD player will be displayed on the AV receiver.

•Set it to

“Off” when a connected piece of equipment is not

compatible or it is unclear whether the equipment is compatible

or not.

• If operation is not normal when set to

“On”, change the setting

“Off”.

• Refer to the connected component’s instruction manual for

details.

•When “HDMI Control(RIHD)” setting is set to “On”, the

power consumption on standby mode slightly increases.

(Depending on the TV status, the AV receiver will enter standby

mode as usual.)

Hardware Setup

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds) (➔ page 41).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R990 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info