Bedienungsanleitung Onkyo HT-R993 (Seite 9 von 70) (Englisch, Französisch, Spanisch)

577745

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Step 2:

Setting Up

After placing the microphone at the measurement

position, select "Do it Now" with the cursors and

press ENTER.

When "Please plug microphone that came in a

box with AV receiver." is displayed, connect the

microphone to the SETUP MIC jack of the unit

SETUP MIC jack

Speaker

setup

microphone

Follow the guidance displayed on the TV screen.

AccuEQ Room Calibration

Front Speakers Type

Height Speakers Type

Powered Zone 2

Subwoofer

Normal

Not Use

Yes

Select the speaker type you use as height speaker.

ENTER Nex t

When the screen above is displayed, press ENTER

on the remote controller. On the next screen, the

subwoofer's power supply will be confirmed. Check and

press ENTER on the remote controller. On the next

screen, installation of the speaker setup microphone will

be confirmed. Check and press ENTER on the remote

controller.

The test tones sound from the connected speakers

and automatic speaker setting starts.

Measurement will be made twice for each speaker. It

takes several minutes to be completed. Keep the room

as quiet as possible during measurement. If any of

the speakers do not produce the test tone, check for

disconnection.

 During measurement, each speaker outputs the test

tones at a high volume. Be careful of sound leak

that may disturb your neighbors, or be careful not to

frighten young children.

When the measurement is completed, the

measurement result is displayed.

Press

on the remote controller to check the settings.

Press ENTER with "Save" selected.

 If there is an error message, follow the on-screen

instruction to remove the error cause.

 Due to the electrical complexities and the interaction

with the room, you may notice irregular results when

setting the level or distance of each speaker with

automatic speaker setup. If so, you may need to

adjust the speaker level or other settings manually

listening to the actual sound.

When "Please unplug setup microphone." is

displayed, disconnect the microphone.



2nd Step : Source Connection

You can check whether or not each input source is

connected correctly.

When the Source Connection start screen is

displayed, select "Yes, Continue" with the cursors

and press ENTER.

This step will start to check if the

connections were made correctly.

Would you like to continue?

Yes. Continue

No. Skip

Initial Setup

Source Connection

ExitHOME

Select the desired input to check the connection and

press ENTER.

Start playback of the selected device. If connection is

correct, video/audio of the input source selected on the

unit will be played.

After checking the connection, select "Yes" with the

cursors and press ENTER.

 If you select "No" and press ENTER, the error cause

will be displayed. Follow the guidance to remove the

error cause and check the connection again.

Select "Yes" with the cursors and press ENTER

on the remote controller to check the connection

of other inputs or select "No, Done Checking" and

press ENTER to skip.

If you select "Yes", you will return to the screen of step 2.

If you select "No, Done Checking", you will proceed to

step 5.

Enabling HDMI Linked Operation and Other

Functions

In the next screen, you can enable the HDMI linked

operation with CEC compliant device, connection with

ARC compatible TV, and HDMI Through function. Using

the cursors on the remote controller, select "Yes" to

enable them or "No, Done Checking" to skip, and then

press ENTER.

Select "Yes" with the cursors and press ENTER to

enable the CEC link function or select "No" and

press ENTER to keep it disabled.

The following CEC-compatible devices are found;

Do you wish to turn on the CEC link?

Integra DHS-8.8

Yes

Source Connection

HOME Exit

If you select "Yes", the connection with ARC compatible

TV and HDMI Through function will be set to "Auto" and

enabled.



3rd Step : Remote Mode Setup

HOME E x it

Initial Setup

Remote Mode Setup

Preprograming remote will give you control

of other devices from AV receiver remote

Would you like to setup your remote to

control your devices? This may take a while

depending on what and how many you have

connected. You can always come back to remote

setup from setup “8-2 Remote Mode Setup”.

Yes

No. Skip

You can enable operation of the other components

using the remote controller of the unit. When the

Remote Mode Setup start screen is displayed, select "Yes"

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R993 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R993

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info