Bedienungsanleitung Onkyo HT-S5100 (Seite 42 von 124) (Englisch)

455823

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

First Time Setup

This section explains the settings that you need to make before using the AV receiver for the very ﬁrst time.

With the supplied calibrated microphone, Audyssey 2EQ

automatically determines the number of speakers con-

nected, their size for purposes of bass management,

optimum crossover frequencies to the subwoofer (if

present), and distances from the primary listening posi-

tion. Audyssey 2EQ then removes the distortion caused

by room acoustics by capturing room acoustical prob-

lems over the listening area in both the frequency and

time domain. The result is clear, well-balanced sound for

everyone. Enabling Audyssey 2EQ allows you to also

use Audyssey Dynamic EQ, which maintains the proper

octave-to-octave balance at any volume level. (See

page 76)

Measurement Positions

To create a listening environment in which several

people can enjoy your home theater simultaneously,

Audyssey 2EQ takes measurements at three positions

within the listening area.

A First measurement point

This is the center point of the listening area, or the

listening position.

B Second measurement point

The right side of the listening area.

C Third measurement point

The left side of the listening area.

The distances between points

1 and 2 and points 1

and

3 must be at least 1 meter.

From the examples below, choose the listening area that

best matches yours and place the microphone accord-

ingly when prompted.

Using Audyssey 2EQ

Notes:

• For all measurements, the microphone capsule should

point directly at the ceiling.

• If there’s an obstacle between the microphone and any

speaker, the automatic setup will not work correctly.

Set up the room as you would when enjoying a DVD.

• Positioning the microphone close to where your ears

would normally be will provide better results. You can

adjust the height of the microphone by using a tripod

or level table.

• Do not attempt to hold the microphone in your hand

during measurements as this will produce incorrect

results.

Automatic Speaker Setup

(Audyssey 2EQ)

TV TV TV

Listening area

Listening position

Turn on the AV receiver.

Put the speaker setup micro-

phone at measurement point

(see left), and connect it to the

SETUP MIC jack.

Notes:

• If the AV receiver is muted, it will be unmuted

automatically when the automatic speaker setup

starts.

• Automatic speaker setup cannot be performed

while a pair of headphones is connected.

• It takes about 10 minutes to complete the auto-

matic speaker setup for three positions. Total mea-

surement time varies depending on the speakers.

• Do not connect or disconnect any speakers during

the automatic speaker setup.

ON/STANDBY

STANDBY

SPEAKERS

TONE

MOVIE/TV MUSIC GAME

DISPLAY RT/PTY/TP MEMORY

CLEAR

DIGITAL INPUT TUNING MODE

PHONES

MULTI CH

DOCK

DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD

SETUP

SETUP MIC

VIDEO

L AUDIO R

AUX INPUT

ENTER

RETURN

TUNING PRESET

MASTER VOLUME

AV RECEIVER

HT-R560

SETUP MIC

2, 6

SETUP MIC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-S5100 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info