Bedienungsanleitung Onkyo M-5000R (Seite 22 von 24) (Englisch)

462126

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Others

Troubleshooting

• Make sure that the power cord is properly plugged into

the wall outlet (➔ 16).

• Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

• When the set ASb starts running, the power amplifier

will automatically go standby (➔ 21).

• If the power amplifier cannot start with the Standby LED

blinking, then it may be problem with the power

amplifier. If speaker cables touch the chassis, this may

cause the power amplifier to short out and make sure the

plus terminals of speaker cables do not touch the chassis

or the minus terminals.

Please try the method below:

–Set the POWER switch to OFF and disconnect all

speaker cables. Check that the top of the set (cooling

vent) is not blocked. When the power amplifier has

cooled down, reconnect all speaker cables and set the

POWER switch to ON. Then Press ON/STANDBY.

• Make sure the speakers are connected correctly (➔ 15).

• Check all connections and correct as necessary (➔ 15).

• When making XLR IN input, make sure that the INPUT

SELECT switch is switched to the XLR side.

• Make sure the correct input source is selected.

• Make sure the analog audio cable is connected correctly.

• Make sure that all audio connecting plugs are pushed in

all the way.

• Make sure the speaker cables are connected with the

correct polarity (➔ 15).

• Make sure all audio connecting plugs are pushed in all

the way (➔ 15).

• The sound quality can be affected by strong magnetic

fields, such as that from a TV. Try moving any such

devices away from the power amplifier.

• If you have any devices that emit high-intensity radio

waves near the power amplifier, such as a cellular phone

that’s being used to make a call, the power amplifier

may output noise.

• When making RCA IN input, make sure that the INPUT

SELECT switch is switched to the RCA side.

• Check the connection in case of bi-amping connection.

• Audio performance will be at its best about 10 to 30

minutes after the power amplifier has been turned on and

had time to warm up.

• Using cable ties to bundle audio cables with speaker or

power cables may degrade the sound quality. So don’t

do it.

• Make sure the cables are connected to the jacks firmly.

Power

Can’t turn on the Power Amplifier.

The Power Amplifier turns off

unexpectedly.

Audio

There’s no sound.

The sound quality is not good.

Audio performance

External Components

The 12V trigger does not work.

The power amplifier contains a microcomputer for

signal processing and control functions. In very rare

situations, severe interference, noise from an external

source, or static electricity may cause it to lockup. In

the unlikely event that this should happen, unplug the

power cord, wait at least 5 seconds, and then plug it

again.

Before disconnecting the power cord from the wall

outlet, set the main power switch to OFF.

If during idling the cover is too hot to touch, then

ventilation needs to be improved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo M-5000R Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo M-5000R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info