Bedienungsanleitung Onkyo PA-MC5500 (Seite 10 von 20) (Englisch)

452194

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Front & Rear Panels—Continued

b INPUT SELECT switch

This switch is located between the balanced input

and single-ended RCA input for each channel. Use

this switch to select the input type for its channel.

When setting the switch to the upper side, the bal-

anced input is selected.

When setting the switch to the lower side, the RCA

audio input is selected.

Notes:

• Do not change the INPUT SELECT switch setting

when the amplifier is turned on.

• Make sure that connections have been made only to

the inputs selected with the INPUT SELECT switches

and nothing is connected to the other ones.

c Unbalanced Input (single end RCA input)

Connect AV controllers or control amplifiers with

single-ended outputs.

Notes:

• When using this single-ended connection for a spe-

cific channel, set the INPUT SELECT switch to the

lower side (the RCA audio input side), use commer-

cial RCA audio pin cable and connect the single-

ended outputs.

• Do not connect anything to the balanced input jack.

d OUTPUT (Speaker output and binding post)

These terminal posts are for connecting the front

L/R, center, surround L/R, surround back L/R, and

front high/wide L/R speakers.

The FRONT L/R and SURR BACK L/R terminal

posts can be used with front speakers and surround

back speakers respectively, or used to bi-amp the

front speakers. See “Bi-amping the Front Speakers”

on page 15.

e SPEAKER IMPEDANCE switch

Use this switch to select the speaker impedance.

4Ω: Select if the impedance of any speaker is

4 ohms or more but less than 6.

6Ω: Select if the impedances of all speakers are

between 6 and 16 ohms.

f AUTO POWER DOWN switch

You can use the auto power-down function. If the

amplifier receives no signal for 3 hours, it will auto-

matically enter standby mode. Once the auto power-

down function has been activated, the amplifier will

not automatically turn on even if it receives the sig-

nal. To turn on the amplifier, press the

ON/STANDBY button manually. You can also dis-

able the function by setting this switch to OFF side.

Default setting: ON (European models), OFF

(North American and Asian models)

Notes:

• Regardless of the position of this switch, this function

will not work when the amplifier has been turned on

by the 12V trigger.

• Before entering standby mode by the auto power-

down function, the amplifier notifies you by flashing

the ON indicator for 10 seconds.

• Depending on some sources, the auto power-down

function may activate during playback.

g 12V TRIGGER IN

Connects to the 12V trigger output terminal on the

other component to control the amplifier. This

enables the amplifier to turn on or go into standby

state based on the power on/standby status of the

connected component.

Use the supplied or commercially available 1/8-inch

mono cable to connect to the 12V trigger output ter-

minal on the other device.

The tip polarity of the connectors are as shown

below.

h AC INLET

Plug the supplied power cord into this AC INLET

and then into the power outlet on the wall.

• Do not plug the amplifier into the AC outlet other than

an AC wall socket.

• Do not use a power cord other than the one supplied

with the amplifier. The power cord supplied is

designed for use with the amplifier and should not be

used with any other device.

• Never have the power cord disconnected from the

amplifier while the other end is plugged into the wall

outlet. Doing so may cause an electric shock. Always

connect by plugging into the wall outlet last and dis-

connect by unplugging from the wall outlet first.

• Before you plug in the amplifier, confirm that all con-

nections have been made properly.

• Turning on the power may cause a momentary power

surge, which might interfere with other electrical

equipment on the same circuit, such as computers. If

this happens, use a wall outlet on a different circuit.

RCA type

5 to 12 volts, positive

tip polarity

To an AC wall

outlet

Power cord

(supplied)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PA-MC5500 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo PA-MC5500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info