Bedienungsanleitung Onkyo PR-SC5508 (Seite 87 von 108) (Englisch)

452195

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Tip

• If you cannot access the database, a message “Cannot

connect to database.” will appear. Press ENTER to

return to the previous step.

• If the brand name is not found, use r to select “Not

Listed”, and then press ENTER.

The following screen appears.

Use q/w to select “Search by model number

(via network)”, and then press ENTER.

The model number input panel appears.

When you do NOT have a network connection

or if you are not sure about the exact model,

select “Skip”, and then press ENTER.

If you select “Skip”, you will go to step 11.

Enter the model in a similar manner as in the

case of the brand name (step 6).

Tip

• After entering the 3rd character, press ENTER to start

searching.

• You cannot enter a space character.

Use q/w to select the model, and then press

ENTER.

If the model is not found, use r to select “Not

Listed”, and then press

ENTER.

After searching is completed, a message for

remote control code transfer will appear.

While pointing the remote controller at the AV

controller’s remote control sensor, press

ENTER.

8–1. Remote Mode Setup

Skip

Search by model number (via network)

Category

Brand

Model

Sonic

(Option)

8–1. Remote Mode Setup

Category

Brand

Model

XXXXX

xxxxx

Now we are ready to transfer data to the remote.

Please hold the remote so that it is facing the receiver.

Use ENTER button of your remote to activate “OK”.

Ready?

Approx.

16ft. (5 m)

Incoming sensor

Remote control sensor (Transmitter)

15° off center

(Left/Right/Up/Down)

When you searched for the model, a message

“Successful” will appear. Now the transfer is

successful!

Go to step 15.

When you did NOT search for the model, the

following screen appears.

Push any key (except for arrow buttons and

ENTER) to see if the component responds.

When category other than TV have been selected,

the content is different.

Asterisks in [***/***] mean the order of the candi-

date code and the total number of the codes for the

brand.

If you can control component, press

RECEIVER, use q/w to select “Works”, and

then press ENTER.

If you cannot control component, press

RECEIVER, use q/w to select “Doesn’t work

(Retry)” and press ENTER.

The next code appears. Repeat from step 11.

Press ENTER to transfer the determined code.

Press ENTER.

You’ll return to the category selection menu.

Press SETUP to end the remote mode setup.

8–1. Remote Mode Setup

Works

Doesn’t work (Retry)

1. Push some key to see if the TV responds.

(except Arrow and Enter.)

2. Choose “Works” or “Doesn’t work”.

Category

Brand

Code

XXXXX

xxxxx[***/***]

*1 *2

8–1. Remote Mode Setup

Now we are ready to transfer data to the remote.

Please hold the remote so that it is facing the receiver.

Use ENTER button of your remote to activate “OK”.

Ready?

Category

Brand

Code

XXXXX

xxxxx[***/***]

Approx.

16ft. (5 m)

Incoming sensor

Remote control sensor (Transmitter)

15° off center

(Left/Right/Up/Down)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PR-SC5508 Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo PR-SC5508

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info