Bedienungsanleitung Onkyo PR-SC5530 (Seite 10 von 24) (Englisch)

553774

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Step 2:

Setting Up

After placing the microphone at the measurement

position, select "Do it Now" with the cursors and

press ENTER.

Connect the microphone to the SETUP MIC jack of the unit.

SETUP MIC jack

Speaker setup

microphone

Follow the guidance displayed on the TV screen.

AccuEQ Room Calibration

Front Speakers Type

Height 1 Speakers Type

Height 2 Speakers Type

Normal

Not Use

Set bi-amp only if you use 2 channel amp for each front speaker.

ENTER Nex t

REAR PANEL

SURROUND

WIDE

BACK

FRONT R FRONT L

When the screen above is displayed, set the items with

the cursors on the remote controller. Select the types for

height 1/2 speakers if the Height speakers are used. After

front and Height speakers types are selected, switch the

screen using cursor

to select the type of subwoofer.

After setting the items, press ENTER on the remote

controller. Press ENTER again in the next screen to start

automatic speaker setting.

r When the cursor is on an item, the content of the item

will be shown on the lower left of the screen.

The test tones sound from the connected speakers

and automatic speaker setting starts.

Measurement will be made twice for each speaker. It

takes several minutes to be completed. Keep the room

as quiet as possible during measurement. If any of

the speakers do not produce the test tone, check for

disconnection.

r During measurement, each speaker outputs the test

tones at a high volume. Be careful of sound leak

that may disturb your neighbors, or be careful not to

frighten young children.

When the measurement is completed, the

measurement result is displayed.

Press

on the remote controller to check the

settings.

Press ENTER with "Save" selected. In the next

screen showing that "AccuEQ Room Calibration" is "On",

press ENTER on the remote controller.

r If there is an error message, follow the on-screen

instruction to remove the error cause.

About THX playback

THX recommends setting the speakers manually if you

use THX-certified speakers or playing back with THX

listening modes.

r

THX recommends setting the crossover frequency to

“80Hz(THX)” manually.

r

Due to the electrical complexities and the interaction

with the room, you may notice irregular results when

setting the level or distance of each speaker. If this

happens, THX recommends setting the speakers and

the subwoofer manually.

When "Please unplug setup microphone." is

displayed, disconnect the microphone.



2nd Step : Source Connection

You can check whether or not each input source is

connected correctly.

When the Source Connection start screen is displayed,

select "Yes, Continue" with the cursors and press ENTER.

This step will start to check if the

connections were made correctly.

Would you like to continue?

Yes, Continue

No. Skip

Initial Setup

Source Connection

ExitHOME

Select the desired input to check the connection and

press ENTER.

Start playback of the selected device. If connection is

correct, video/audio of the input source selected on the

unit will be played.

After checking the connection, select "Yes" with the

cursors and press ENTER.

r If you select "No" and press ENTER, the error cause

will be displayed. Follow the guidance to remove the

error cause and check the connection again.

Select "Yes" with the cursors and press ENTER

on the remote controller to check the connection

of other inputs or select "No, Done Checking" and

press ENTER to skip.

If you select "Yes", you will return to the screen of step 2.

If you select "No, Done Checking", you will proceed to step 5.

Enabling HDMI Linked Operation and Other

Functions

In the next screen, you can enable the HDMI linked

operation with CEC compliant device, connection with

ARC compatible TV, and HDMI Through function. Select

"Yes" with the cursors to enable them or "No, Done

Checking" to skip, and press ENTER on the remote

controller.

Select "Yes" with the cursors and press ENTER to

enable the CEC link function or select "No" and press

ENTER to keep it disabled.

The following CEC-compatible devices are found;

Do you wish toturnon the CEC link?

Integra DHS-8.8

Yes

Source Connection

ExitHOME

If you select "Yes", the connection with ARC compatible TV

and HDMI Through function will be set to "Auto" and enabled.



3rd Step : Remote Mode Setup

HOME Ex it

Initial Setup

Remote Mode Setup

Preprograming remote will give you control

of other devices from AV receiver remote

Would you like to setup your remote to

control your devices? This may take a while

depending on what and how many you have

connected. You can always come back to remote

setup from setup “8-2 Remote Mode Setup”.

Yes

No. Skip

In this step, you can enable operation of the other

components using the remote controller of the unit. When

the Remote Mode Setup start screen is displayed, select

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PR-SC5530 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo PR-SC5530

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info