Bedienungsanleitung Onkyo PR-SC886 (Seite 129 von 134) (Englisch)

61148

129

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

129

Troubleshooting—Continued

There’s no picture from a source connected to

an HDMI IN

• When the “Monitor Out” setting is set to “Analog”,

and the “Resolution” setting is set to anything other

than “Through” (see page 49), no video is output by

the HDMI OUT.

• If the message “Resolution Error” appears on the AV

controller’s display, this indicates that your TV does

not support the current video resolution and you need

to select another resolution on your DVD player.

The onscreen menus don’t appear

• If your TV is connected to the analog outputs, set the

“Monitor Out” setting to “Analog” (page 46).

• On your TV, make sure that the video input to which

the AV controller is connected is selected.

•

On non-North American models, specify the TV system

used in your area in the “TV Format Setup

(not North American models)” on page 56.

The immediate display does not appear

• The immediate display will not appear when the input

signal from the COMPONENT VIDEO IN is output to

a device connected to the COMPONENT MONITOR

OUT 1 or 2.

• Depending on the input signal, the immediate display

may not appear when the input signal from the HDMI

IN is output to a device connected to the HDMI OUT.

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

•

Move the AV controller away from your TV or com-

puter.

• Listen to the station in mono (page 67).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 15).

• Make sure that the remote controller is not too far

away from the AV controller, and that there’s no

obstruction between the remote controller and the AV

controller’s remote control sensor (page 15).

• Make sure you’ve selected the correct remote control-

ler mode (page 16).

• Make sure you’ve entered the correct remote control

code (page 122).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 15).

• Make sure that the AV controller is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

•

If the AV controller is installed in a rack or cabinet with

colored-glass doors, the remote controller may not work

reliably when the doors are closed.

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

• Make sure to set the same ID on both the AV controller

and remote controller (page 110).

Can’t control other components

• If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work (page 44).

• Make sure you’ve selected the correct remote control-

ler mode (page 16).

• If you’ve connected an u-capable Onkyo MD

recorder, CD recorder, u Dock to the TAPE IN/OUT

jacks, or an u Dock to the AUX 1 jacks, for the

remote controller to work properly, you must set the

display to MD, CDR, or DOCK (page 57).

If you cannot operate it, you will need to enter the

appropriate remote control code (page 122).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

• If none of the codes work, use the Learning function

to learn the commands of the other component’s

remote controller (page 125).

• With some AV components, certain buttons may not

work as expected, and some may not work at all.

• To control an Onkyo component that’s connected via

u, point the remote controller at the AV controller.

Be sure to enter the appropriate remote control code

first (page 123).

• To control an Onkyo component that’s not connected

via u, or another manufacturer’s component, point

the remote controller at that component. Be sure to

enter the appropriate remote control code first

(page 122).

Can’t learn commands from another remote

controller

• When learning commands, make sure that the trans-

mitting ends of both remote controllers are pointing at

each other.

• Are you trying to learn from a remote controller that

cannot be used for learning? Some commands cannot

be learned, especially those that contain several

instructions.

Tuner

Remote Controller

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PR-SC886 Seite 129

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info