Bedienungsanleitung Onkyo SKF-940F (Seite 19 von 68) (Englisch)

601409

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Connecting Your Speakers

Read the following before connecting your speakers:

•You can connect speakers with an impedance of

8 ohms or higher

. If you use speakers with a lower

impedance, and use the ampliﬁer at high volume lev-

els for a long period of time, the built-in protection

circuit may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

•Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals to only positive

(+) terminals, and negative (–) terminals to only nega-

tive (–) terminals. If you get them the wrong way

around, the sound will be out of phase and will sound

unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the

positive and negative wires.

Doing so may damage the AV

receiver.

• Don’t connect more than one

cable to each speaker termi-

nal. Doing so may damage the

AV receiver.

• Don’t connect one speaker to several terminals.

The AV receiver’s positive (+) speaker terminals and

speaker’s positive (+) terminals are color-coded for ease

of identiﬁcation. (The negative (–) speaker terminals are

all black.) Match the color of each cable to the corre-

sponding speaker terminal.

Note:

When speaker set B is turned on, speaker set A is reduced

to 5.1-channel playback.

Speaker Connection Precautions

DVD

ONITOR

OUT

SURROUND BACK

SPEAKERS

SURROUND

SPEAKERS

PRE OUT

SUB

WOOFER

SUB

WOOFER

URROUND

SURR BACK

CENTER

FRONT

SPEAKERS A

FRONT

SPEAKERS B

AV RECEIVER

AC OUTLET

AC 230-240V

SWITCHED

100W MAX.

50Hz

CENTER

SPEAKER

SURROUND BACK

SPEAKERS

SURROUND

SPEAKERS

FRONT

SPEAKERS A

CENTER

SPEAKER

PRE OUT

SUB

WOOFER

LINE INPUT

Red

Green

White

Blue

Gray

Brown

Ta n

Subwoofer Front Right Center Front Left

Surround

Back Right

Surround

Right

Surround

Back Left

Surround

Left

Connecting Speaker Set A

Speaker terminal Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

On the AV receiver, unscrew the terminal. Fully

insert the bare wires. Make sure that the bare wire

is touching the inside of the pole. Screw the termi-

nal tight.

On the speakers, loosen the binding posts.

Insert the speaker wires

into the binding posts as

shown, then tighten the

binding posts.

Using the supplied RCA cable, connect the AV

receiver’s SUBWOOFER PRE OUT to LINE

INPUT on the subwoofer.

Make sure the cable is plugged all the way.

Connecting Speaker Set B (sold

separately)

Strip 3/8" (10 mm) of insu-

lation from the ends of the

speaker cables, and twist

the bare wires tightly, as

shown.

While pressing the lever, insert

the wire into the hole, and then

release the lever.

Make sure that the terminals are

gripping the bare wires, not the

insulation.

3/8" (10 mm)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo SKF-940F Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info