Bedienungsanleitung Onkyo SKW-208 (Seite 6 von 12) (Deutsch, Englisch)

549890

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

En-6

Adjustments

Crossover frequency and output level

• Adjust the SKW-208 output level and crossover fre-

quency to suit your listening room and connected

speakers.

• Be aware that you might set the subwoofer to a high

output level because superbass-range sound is less

audible than other sound ranges. To obtain well-bal-

anced frequency characteristics, set the output level

to a slightly lower level than seems optimal. (This

will also prevent the input of signals that are too

strong.)

Note:

Be careful not to allow the input of excessive power.

Input levels that greatly exceed normal situations can

damage the SKW-208. Also note that switching opera-

tions at the amplifier may generate excessive noise that

may result in damage. When using switches at the ampli-

fier, first lower the volume to prevent accidental damage.

Placement

The placement of the SKW-208 can greatly affect the

sound that is produced. In general, a good bass sound

can be obtained by installing the subwoofer in a front

corner, or at one-third the width of the wall, as shown.

Troubleshooting

The unit does not turn on

• The power plug is not fully inserted.

➞ Insert the power plug fully into the power outlet.

No sound is output

• The OUTPUT LEVEL knob is set to the MIN level.

➞ Set the OUTPUT LEVEL knob properly.

• Pin connector cable is not properly connected to the

LINE INPUT jack.

• The speaker setting at the amplifier (or receiver) is

incorrect.

➞ Check the settings at the amplifier (or receiver).

• The input signal is so small that the unit entered

Standby mode.

➞ Slightly increase the output level at the amplifier

(or receiver).

• If the STANDBY/ON indicator lights up (both red and

blue LEDs) several seconds or minutes after the sound

output stopped, this means that the amp protection cir-

cuit has been activated. In this case, set the OUTPUT

LEVEL knob to the center position, and disconnect

the power cord from the AC outlet. Wait at least 10

seconds, and then reconnect the power cord. If that

doesn’t solve the issue, contact your Onkyo dealer.

Low sound output

• The sound source might not include a superbass range.

➞ Play a sound source that includes a superbass

range.

Hum noise

• Pin connector plug is not inserted completely.

➞ Fully insert the pin connector plug.

• External leakage flux (induction noise by TV, etc.)

occurs.

➞ Relocate the SKW-208 away from the noise

source and re-connect.

Specifications

Type Bass-reflex with built-in

power amplifier

Input sensitivity/impedance

550 mV / 20 k

Frequency response 25–200 Hz

Rated output power 120 watts minimum contin-

uos power, 4 ohms, driven at

100 Hz with a maximum total

harmonic distortion of 1 %

Cabinet capacity 37 L (1.3 cubic feet)

Drivers unit 25 cm (10 inch) cone woofer

Power supply AC 230 V, 50 Hz

Power consumption 150 W

Dimensions (W  H  D) 275  507  411 mm

(10-13/16"  19-15/16" 

16-3/16")

Weight 11.6 kg (25.6 lbs.)

Accessory Pin connector cable (1 pc.)

Instruction manual (this man-

ual)

Floor pad (4 pcs.)

Others Auto standby

Specifications and appearance are subject to change

without prior notice.

Corner

1/3 room

length

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo SKW-208 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info