Bedienungsanleitung Onkyo TX-8555 (Seite 34 von 48) (Englisch)

462131

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Advanced Setup—Continued

1.Hardware set

Remote ID

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the receiver from the other components, you can change

its remote ID from 1, the default, to 2 or 3.

Note:

• If you do change the receiver’s remote ID, be sure to

change the remote controller to the same ID,

otherwise, you won’t be able to control it with the

remote controller.

Impedance

See page 15.

Z2 Out

See page 36.

2.Intelli Vol

With IntelliVolume, you can set the input level for each

input selector individually. This is useful if one of your

source components is louder or quieter than the others.

Use the Left and Right [ ]/[ ] buttons to set the level.

If a component is noticeably louder than the others, use

the Left [ ] button to reduce its input level. If it’s

noticeably quieter, use the Right [ ] button to increase

its input level. The input level can be adjusted from -12

dB to +12 dB in 1 dB steps.

Note:

• IntelliVolume does not apply for Zone 2.

3.Volume Setup

Volume Disp (Volume Display)

With this setting, you can select the Abs (Absolute) or

Rel (Relative) volume display mode.

Muting Lvl (Muting Level)

With this setting, you can set the Muting Level.

The range is -00dB, -50dB, -40dB, -30dB, -20dB,

-10dB.

MaxVolume (Maximum Volume)

With this setting, you can limit the maximum volume.

The Maximum Volume range is Off, 79 to 30.

Pow On Vol (Power On Volume)

This setting determines the volume level applied each

time the receiver is turned on.

The range is Last, Min, 1 to 79, Max.

To use the same volume level as when the receiver was

last turned off, select Last.

Note:

• The Power On Volume setting cannot be set higher

than the Maximum Volume setting.

Z2MaxVol (Zone 2 Maximum Volume)

With this setting, you can limit the maximum volume for

Zone 2.

The Maximum Volume range is Off, 79 to 30.

Z2POnVol (Zone 2 Power On Volume)

This setting determines the volume level applied for

Zone 2 each time the receiver is turned on.

The range is Last, Min, 1 to 79, Max.

To use the same volume level as when the receiver was

last turned off, select Last.

4.Tuner Setup

See “Using XM/SIRIUS Satellite Radio.”

5.Lock Setup

With this setting, you can protect your settings by

locking the setup menus.

Locked: Setup menus locked.

Unlocked: Setup menus unlocked.

When Locked is selected, only this Lock Setup item can

be accessed.

Advanced Setup Menu

Changing the Remote Controller’s ID

While holding down the

[RECEIVER] REMOTE MODE

button, press and hold down the

[SUBTITLE] button until the

REMOTE MODE button lights up

(about 3 seconds).

Use the number buttons to enter

ID 1, 2, or 3.

The [RECEIVER] REMOTE MODE

button ﬂashes twice.

If programming fails, the button ﬂashes

once. Repeat steps 1 and 2.

and

(3 seconds)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-8555 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-8555

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info