Bedienungsanleitung Onkyo TX-DS494 (Seite 8 von 36) (Englisch)

553751

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Front panel facilities

7 DIMMER button

Press to set the brightness of the front display. The brightness

changes to normal and dim.

• The dimmer control for the front display can also be performed

by using the remote controller.

8 MASTER VOLUME dial

The MASTER VOLUME dial is used to control the volume level.

Turn the dial clockwise to increase the volume level and

counterclockwise to decrease it.

9 PHONES jack

This is a standard stereo jack for connecting stereo headphones.

The audio for the front right and left speakers are sent to the

headphone speakers. When the headphones are plugged in, the

listening mode automatically changes to STEREO and sounds are

not output from the speakers.

0 AUDIO SELECTOR button

Press to select an audio input signal format other than FM, AM and

PHONO. Each time this button is pressed, the setting cycles;

“AUTO” → “MULTI CH” → “ANALOG” → “AUTO” (back to

the beginning) (refer to page 23).

Input Selector Buttons (DVD, VIDEO 1, VIDEO 2,

TAPE, FM, AM, PHONO, and CD)

These buttons are used to select the input source. Pressing and

holding the TAPE button for about 2 seconds allows the TAPE and

MD sources to be switched.

= BASS and TREBLE control knobs

Boosts or cuts the bass and treble response.

BASS:

Adjusts the bass response from the Front speakers and

headphones. Turn the knob clockwise to boost the bass response.

Turn the knob counterclockwise to cut the bass response.

TREBLE: Adjusts the treble response from the Front speakers

and headphones. Turn the knob clockwise to boost the treble

response. Turn the knob counterclockwise to cut the treble

response.

~ Remote control sensor

This sensor receives the control signals from the remote controller.

! SP SEL button

Press to select the optimum speaker configuration.

@ SW MODE button

Press to select the subwoofer mode.

# DIGITAL INPUT button

When digital components are connected to the DIGITAL INPUT

jacks of the TX-DS494, use this button to assign the DIGITAL

INPUT jacks to them according to their forms of connection.

$ FM MODE button

Press to switch the reception mode between stereo and monaural.

If audio is interrupted or noise interferes with audio during FM

stereo broadcasting, press this button to switch to the monaural

reception mode.

% MEMORY button

This button is used to assign the radio station that is currently

tuned in to a preset channel or delete a previously preset station.

^ TUNING ™/£ buttons

Use these buttons to change the tuner frequency. The tuner

frequency is displayed in the front display and it can be changed in

50 kHz increments for FM and 10 kHz (or 9 kHz) increments for

AM.

When FM is selected, you can hold down one of the TUNING ™/£

buttons and then release it to activate the auto-search feature. It will

search for a station in the direction of the button you pressed and stop

when it tunes into one.

& PRESET ™/£ buttons

These buttons make it possible to store desired radio stations under

the desired preset numbers and recall them with an easy operation.

* Display

ASPEAKERS A/B indicators

Shows the current speaker system in use.

BSLEEP indicator

Lights up when the sleep timer is active.

CSource/Listening mode indicators

One of these indicators lights to show the format of the current

source as “PCM DIGITAL”, “Ÿ DIGITAL” or “DTS”. In

addition, one of the listening mode indicators “Ÿ PRO

LOGIC II”, “DSP” and “STEREO” lights according to the

current listening mode.

DMUTING indicator

Flashes when the mute function is active.

EFM STEREO indicator

Lights up when an FM stereo broadcast station is received.

FTUNED indicator

Lights up when a radio station is received.

GMEMORY indicator

Lights up when the MEMORY button is pressed in the radio

station preset operation.

HFM MUTE indicator

Lights up to indicate FM muting. It extinguishes when the

monaural reception mode is started by pressing the FM MODE

button.

IRDS indicator (European models only)

Lights up when a RDS station is received.

JMulti function display

In usual operation, shows the current input source and volume.

When the FM or AM input is selected, it shows the frequency

and preset number. When the DISPLAY button is pressed, it

shows the listening mode and input source format. However, it

does not show the source format when the FM or AM source is

selected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS494 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS494

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info