Bedienungsanleitung Onkyo TX-DS494 (Seite 28 von 36) (Englisch)

553751

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

To enjoy Surround mode

Selecting Onkyo’s surround modes

1. Press an input selector button to select the

desired sound source.

2. Press the DSP button repeatedly until the

desired surround mode name appears.

The selected mode appears in the display. Each time you press

the button, the surround mode changes as follows:

3. Play the selected sound source.

When software compatible with Dolby Digital is played, the

surround mode will automatically switch to the DOLBY D

surround mode. When software compatible with DTS is

played, the surround mode will automatically switch to the

DTS mode.

You can adjust the level of each speaker.

1. Press the CH SEL button on the remote controller to select a

speaker.

2. Press the LEVEL 5/∞ buttons on the remote controller to

raise or lower the level.

• The speaker levels set here are cleared when this unit is set to

STANDBY. (The speaker levels return to the levels set using

the test tone.)

• When the TEST TONE button on the remote controller is

pressed after the above adjustment, the set levels will become

the levels adjusted using the test tone by overwriting the

existing ones.

Selecting STEREO modes

1. Press an input selector button to select the

desired sound source.

2. Press the STEREO button.

3. Play the selected sound source.

Selecting DOLBY DIGITAL/DTS surround

1. Press an input selector button to select the

desired sound source.

2. Press the Ÿ/DTS SURROUND button.

3. Play the selected sound source.

You can adjust the level of each speaker.

1. Press the CH SEL button on the remote controller to select a

speaker.

2. Press the LEVEL 5/∞ buttons on the remote controller to

raise or lower the level.

• The speaker levels set here are cleared when this unit is set to

STANDBY. (The speaker levels return to the levels set using

the test tone.)

• When the TEST TONE button on the remote controller is

pressed after the above adjustment, the set levels will become

the levels adjusted using the test tone by overwriting the

existing ones.

Note:

Sources other than Dolby Digital/DTS-encoded ones are reproduced

with Dolby Pro Logic II.

Late Night function

Since the audio in movies produced for theaters has a big

difference between the highest and lowest levels (dynamic range),

it is sometimes necessary to increase the volume to a very high

level when you want to listen to low-level audio such as

environmental sounds and low human voices. In such a case,

switch the Late Night function to ON to reduce the dynamic range

so that even low-level audio can be identifiable without increasing

the overall listening volume.

This function is especially convenient when you have to view a

movie at a low volume in the night time, etc.

During Dolby Digital surround playback, press the

DSP button.

Each press of the button switches the Late Night function ON and

OFF alternately.

Notes:

• The Late Night function is available only in Dolby Digital

Surround mode.

• The degree of the Late Night effect is already programmed

into the source materials. Some materials may produce only

small or no effects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS494 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS494

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info