Bedienungsanleitung Onkyo TX-DS595 (Seite 50 von 52) (Englisch)

553752

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Troubleshooting guide

If a problem occurs while you are using the remote controller, first

try to operate the controls on the front panel of the TX-DS595 to

make sure that it is not due to a malfunction (or worn out batteries) in

the remote controller.

POWER

Power shuts off immediately after power on.

• Amplifier protection circuitry has been activated.

➞ Remove the power cord from outlet immediately. Contact

your Onkyo service center.

No power.

• Power cord is disconnected.

➞ Connect power cord.

• External noise in the affecting the internal microcomputer.

➞ Turn the power button off and then on again or remove the

power cord from the outlet and then plug it in again.

• Internal fuse is blown.

➞ Contact your Onkyo Service Center.

Power turns on but no sound.

•“MUTING” is displayed.

➞ Press the MUTING button on the remote controller to turn it

off.

• Bad connections or wiring.

➞ Check connections, speaker cables, etc.

• Amplifier protection circuitry has been activated.

➞ Contact your Onkyo Service Center.

The sound of the playback source is not heard.

• Input selector is not set properly.

➞ Set to correct input source.

• Headphones are connected.

➞ Lower volume and then disconnect headphones.

Pressing the ON button on the remote controller does

not turn on the power to the main unit.

• You have not pressed RCVR MODE button.

➞ Press the RCVR MODE button, then press the ON button.

SPEAKERS

No sound from the center speaker, or at very low

volume.

• Speaker cable is not connected.

➞ Check the connection between the amplifier and the speaker.

• Listening mode is set to Stereo or Direct.

➞ Set the Listening mode to any mode other than Stereo or

Direct. The output to the center speaker may differ depending

on the listening mode.

• Center speaker level is set to minimum.

➞ Set the Center speaker level to the appropriate volume (page

20).

• Center speaker is set to “NONE.”

➞ Set CENTER to “LARGE” or “SMALL” (page 19).

No sound or very low volume from subwoofer.

• Subwoofer is set to “NO.”

➞ Check the speaker setting (page 19).

• Subwoofer speakers output level setting is improper.

➞ Check the output level of the Subwoofer using the test tone

(page 19).

Low frequency humming is heard.

• Not properly grounded.

➞ Check outer conductor of input plugs.

• Turntable motor is not properly grounded.

➞ Check for proper ground connection.

• Audio connection cables on the rear panel are connected

incorrectly.

➞ Adjust the placement of the cable to reduce hum.

Howling is heard when the volume is turned up.

• Turntable and speakers are located too close together.

➞ Move them farther apart.

Rough or scratchy sound is heard. High range is not

clear.

• The needles of turntable is dirty or worn, or a problem exists

with a connected component.

➞ Refer to the instruction of the connected components and

check for problem.

• Treble control is too high.

➞ Turn treble down.

FM/AM TUNER

AM stations cannot be received.

• AM loop antenna is not connected.

➞ Connect the included AM loop antenna to the AM antenna

terminals.

Buzzing noise on AM stations (particularly noticeable at

night or with weak stations).

• Noise from electrical apparatus such as fluorescent lamp.

➞ Move the AM loop antenna to different position.

➞ Set up an outdoor AM antenna.

Noise is heard at high-pitched sounds on AM stations.

• Noise from TV set.

➞ Place the AM loop antenna as far as possible from the TV.

➞ Move unit away from TV set.

Crackling noise on both AM and FM stations.

• Noise caused by fluorescent lamp being turned on and off.

➞ Move antenna as far as possible from the fluorescent lamp.

• Noise from automobile ignition.

➞ Install an FM outdoor antenna as far as possible from the

road.

➞ Change the position or direction of the outdoor antenna.

The indicators light for stereo reception, but sound is

distorted and stereo separation is bad.

• Station is too strong.

➞ Change to FM indoor antenna.

• Multiple reflection of the radio waves because of tall buildings

or mountains.

➞ Use antenna that has better directivity and select a point

where distortion is least.

Indicators for stereo reception flicker and hiss is heard

on FM stations.

• Station is too weak.

➞ Install an outdoor FM antenna.

• Stereo FM broadcasts cover only about half the distance of an

ordinary broadcast.

➞ Change the position or direction of the outdoor antenna.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS595 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS595

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info