Bedienungsanleitung Onkyo TX-DS696 (Seite 3 von 64) (Englisch)

553753

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1. Warranty Claim

You can find the serial number on the rear panel of this unit. In case

of warranty claim, please report this number.

2. Recording Copyright

Recording of copyrighted material for other than personal use is

illegal without permission of the copyright holder.

3. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power

does not come on, contact your Onkyo authorized service station.

4. Care

From time to time you should wipe the front and rear panels and the

cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a

weak solution of mild detergent and water, wring it out dry, and

wipe off the dirt. Following this, dry immediately with a clean

cloth. Do not use rough material, thinners, alcohol or other chemi-

cal solvents or cloths since these could damage the finish or remove

the panel lettering.

5. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the area

where this unit will be used meets the required voltage (e.g., AC

230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

Worldwide models are equipped with a voltage selector to conform

to local power supplies. Be sure to set this switch to match the volt-

age of the power supply in your area before plugging in the unit.

For British models

Replacement and mounting of an AC plug on the power supply cord

of this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the

following code:

Blue : Neutral

Brown : Live

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the termi-

nals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal

which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the termi-

nal which is marked with the letter L or coloured red.

IMPORTANT

A 5 ampere fuse is fitted in this plug. Should the fuse need to be

replaced, please ensure that the replacement fuse has a rating of 5

amperes and that it is approved by ASTA or BSI to BS1362. Check

for the ASTA mark or the BSI mark on the body of the fuse.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE

SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND DIS-

POSED OF SAFELY. THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMPERE SOCKET.

If in any doubt, consult a qualified electrician.

Precautions

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

S2898A

21. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to the

appliance, ask the service technician to perform safety checks to

determine that the appliance is in proper operation condition.

23. Wall or Ceiling Mounting – The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other appli-

ances (including amplifiers) that produce heat.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL

ELECTRICAL CODE, ANSI/NFPA 70

For U.S. models

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s at-

tention to Section 820-40 of the NEC which provides guidelines for

proper grounding and, in particular, specifies that the cable ground

shall be connected to the grounding system of the building, as close

to the point of cable entry as practical.

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

For Canadian models

NOTE:

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CA-

NADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modele pour les Canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CON-

FORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA

PRISE ET POUSSER JUSQU’AU FOND.

Onkyo TX-DS696 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS696

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info