Bedienungsanleitung Onkyo TX-DS787 (Seite 18 von 76) (Englisch)

553756

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Example of how to connect your equipment

Connecting your audio components

Below is an example of how you can connect your audio

components to the TX-DS787. Refer to the diagram on pages 16

and 17 for the following connection examples.

1. Connecting a turntable

Using an RCA-type audio connection cable, connect the output

terminal on the turntable to the PHONO IN jacks on the TX-

DS787. Make sure that you properly connect the left channel to the

L jack and the right channel to the R jack.

Note:

The TX-DS787 is designed for use with moving magnet

cartridges. For proper operation, connect a ground (or earth) wire

to the GND terminal. For some turntables, however, connecting

the ground wire may cause increased noise, and in such a case, a

ground wire is not necessary and should not be connected.

2. Connecting a compact disc player

Using an RCA-type audio connection cable, connect the output

terminal on the compact disc player to the CD IN jacks on the TX-

DS787. Make sure that you properly connect the left channel to the

L jack and the right channel to the R jack.

If the compact disc player has a digital output jack as well, be sure

to also connect it to either a DIGITAL INPUT (COAXIAL) or

DIGITAL INPUT (OPTICAL) jack on the TX-DS787 depending

on the type of connector on the compact disc player.

With the initial settings of the TX-DS787, the CD input source is

set for digital input at the OPTICAL 1 jack. If the digital

connection is made at a different jack, this must be changed at the

OSD Menu: Input Setup → Audio Setup → Digital Input (see page

34).

3. Connecting a cassette tape deck, MD recorder,

DAT deck, or CD recorder

Using an RCA-type audio connection cable, connect the output

terminals (PLAY) of the device to the TAPE IN jacks on the TX-

DS787 and the input terminals (REC) to the TAPE OUT jacks.

Make sure that you properly connect the left channel to the L jack

and the right channel to the R jack.

If the device has a digital output jack as well, be sure to also

connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL

INPUT (OPTICAL) jack on the TX-DS787 depending on the type

of connector on the device.

If you connect the device to the DIGITAL INPUT terminal, then

this input source must be set for digital input at the OSD Menu:

Input Setup → Audio Setup → Digital Input.

If the device also has a digital input jack, it can be connected to the

DIGITAL OUTPUT (OPTICAL) jack on the TX-DS787 for

digital recording of the source for REC OUT at the TX-DS787.

Caution:

The output from the DIGITAL OUTPUT jack of the TX-DS787 is

only the digital signal input to the DIGITAL INPUT jack.

Connecting your video components

Below is an example of how you can connect your video

components to the TX-DS787. Refer to the diagram on pages 16

and 17 for the following connection examples.

The flow of the video signals is as follows:

• The signal that comes in from VIDEO IN is sent to VIDEO

OUT.

• The signal that comes in from S VIDEO IN is sent to S VIDEO

OUT

• The signal that comes in from COMPONENT VIDEO IN is

sent to COMPONENT VIDEO OUT.

Caution:

If only the video connection for the MONITOR OUT is made,

even if the input from each source component is through a

component video connection, the picture will not appear. If only

the S video connection for the MONITOR OUT is made, the

picture will not appear.

4. Connecting a DVD player or LD player

Using an RCA-type video connection cable, connect the video

output terminal (composite) on the device to the DVD VIDEO IN

jack on the TX-DS787. If there is an S video output terminal on the

device, connect it to the DVD S VIDEO IN jack using an S video

cable. If the device has component video outputs, connect them to

one of the COMPONENT VIDEO INPUT jacks.

Using an RCA-type audio connection cable, connect the audio

output terminal on the device to the audio DVD IN jacks on the

TX-DS787. Make sure that you properly connect the left channel

to the L jack and the right channel to the R jack.

If the device has a digital output jack as well, be sure to also

connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL

INPUT (OPTICAL) jack on the TX-DS787 depending on the type

of connector on the DVD player.

With the initial settings of the TX-DS787, the DVD input source is

set for digital input at the COAXIAL 1 jack. If the digital

connection is made at a different jack, this must be changed at the

OSD Menu: Input Setup → Audio Setup → Digital Input (see page

34).

5. Connecting a video cassette recorder

Using an RCA-type video connection cable, connect the video

output terminal (composite) on the video cassette recorder to the

VIDEO 2 IN jacks on the TX-DS787 and video input terminal to

the VIDEO 2 OUT jacks. If there is an S video input/output

terminal on the video cassette recorder, connect it to the S VIDEO

2 IN/OUT jack using an S video cable. If the video cassette

recorder has component video outputs, connect them to one of the

COMPONENT VIDEO INPUT jacks.

Using an RCA-type audio connection cable, connect the audio

output terminal on the video cassette recorder to the same VIDEO

2 IN audio jacks on the TX-DS787 and audio input terminal to the

VIDEO 2 OUT audio jacks. Make sure that you properly connect

the left channel to the L jack and the right channel to the R jack.

Onkyo TX-DS787 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS787

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info