553756
65
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
65
Programming the commands of remote controllers for other devices into the remote
controller
OPEN/CLOSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND THX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT DSP
V2 V3 V
ENT
OPEN/CLOSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND THX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT DSP
V2 V3 V
ENT
SEND/LEARN
indicator
MODE
buttons
SEND/LEARN
indicator
MODE
buttons
Erasing the programmed command from one
button
You can only erase memorized commands and not preset ones.
1. Press and hold down the desired MODE button
for the command, press the ENT button, and
then release both buttons.
When you press the MODE button, the SEND/LEARN
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp lights again and LEARN
appears in the display.
2. Press and release the button for the command
you wish to erase.
When you press the button, the SEND/LEARN indicator turns
off and RCV appears in the display. When you release the
button, the lamp lights again.
3. Press and release the same button again.
The SEND/LEARN lamp flashes twice slowly and CLEAR
appears in the display. The memorized command is erased.
Note:
If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, ERROR appears in the display, and the remote
controller exits the programming mode. Resume from Step 1.
Erasing all the commands programmed under a
MODE button
1. Press and hold down the desired MODE
button, press the ENT button twice, and then
release both buttons.
When you press the MODE button, the SEND/LEARN
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp flashes twice slowly and then
lights again.
2. Press and release the same MODE button
again.
When you release the button, the SEND/LEARN indicator
flashes twice slowly. This erases all the commands memorized
to the MODE button.
Notes:
If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three
times quickly and the remote controller exits the programming
mode. Resume from Step 1.
If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly,
ERROR appears in the display, and the remote controller
exits the programming mode. Resume from Step 1.
If many commands have been programmed to the MODE
button, then the SEND/LEARN indicator may remain lit for
some time during Step 2. This is not a malfunction.
65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo TX-DS787 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo TX-DS787

Onkyo TX-DS787 Bedienungsanleitung - Französisch - 74 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info