Bedienungsanleitung Onkyo TX-DS797 (Seite 23 von 76) (Englisch)

553757

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

• The TX-DS797 is shipped with the main power (POWER)

switch in the on position (

). When the power cord is

plugged in for the first time, the TX-DS797 will automatically

enter the standby state and the STANDBY indicator will light

(same condition after step 2 below).

• Before you plug in the TX-DS797, confirm that all connections

have been made properly.

• Turning on the power may cause a momentary power surge,

which might interfere with other electrical equipment on the

same circuit, such as computers. If this happens, use a wall outlet

on a different circuit.

1. Plug the power cord into an AC wall outlet.

2. Press the ON button to turn on the

TX-DS797 (take it out of the standby

state).

To return the TX-DS797 to the standby

state, press the STDBY button.

Turning the power on from the remote controller:

Before you can use the remote controller, you must perform steps 1

and 2 above and place the TX-DS797 in the standby state.

1. Press the RCVR MODE button.

The RCVR MODE button lights green.

Memory preservation

This unit does not require memory preservation batteries. A built-

in memory power backup system preserves the contents of the

memory during power failures and even when the POWER

switch is set to off. The POWER switch must be set to on in order

to charge the backup system.

The memory preservation period after the unit has been turned off

varies depending on climate and placement of the unit. On the

average, memory contents are protected over a period of a few

weeks after the last time the unit has been turned off. This period

is shorter when the unit is exposed to a highly humid climate.

3. Press the STANDBY/ON button to

turn on the TX-DS797. The display

and four jog dial indicators will light

up and the STANDBY indicator will

turn off.

If you press the STANDBY/ON button

again, the receiver returns to Standby mode.

2. Press the POWER switch to set the

TX-DS797 to standby state.

The STANDBY indicator will light up.

To change the display of the input source from TAPE to

MD:

If you connected an MD recorder to the TAPE jack on the TX-

DS797, you can have “MD” appear when the TAPE source button is

pressed. By changing the display, if an Onkyo MD recorder z-

connected, the z system functions will become enabled.

Changing the display:

Press and hold down the TAPE source button until the display

changes from TAPE to MD (approx. 3 seconds).

To return the display to its original setting, perform the same

procedure. This setting is necessary to allow z system functions

for the connected cassette tape or MD recorder.

Connecting the power

Turn off

STANDBY/ON

OFF

POWER

STANDBY

PHONES

MASTER VOLUME

FM AM PHONO C

DTAPE

VIDEO

DVD

OFFZONE

REC OUTDISPLAY DIMMER

UPSAMPLING

AUDIO

SELECTOR

ZONE

()

GRN

REC

()

RED

S VIDEO AUDIO

VIDEO L R

DIGITAL

CLEAR

VCR

VIDEO

/VIDEO CAM INPUT

DSP

RM LISTENING MODE MEMORY

THX

SURROUNDDIRECT STEREO

MEMORY

MODE

ENTER

TURN

SETUP

TUNI

PRESET

RECEIVER

797

RCVR

POWER

TAPE

STANDBY/ON

STDBY

OFF

POWER

STANDBY

STANDBY/ON

STANDBY

TAPE

STANDBY indicator

To wall outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS797 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS797

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info