Bedienungsanleitung Onkyo TX-NR3008 (Seite 112 von 116) (Englisch)

553767

112

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

112

Firmware Update

There are the following methods to update the firmware:

via network and via USB storage. Please choose either one

that suits your condition. Before you start, carefully read

the update procedure. It will take about 60 minutes to

update the firmware.

■ Update via network

You need a wired Internet connection to update the

firmware.

■ Update via USB storage (➔ 113)

Please prepare a USB storage device such as a USB

flash memory stick. You need at least 32 MB of avail-

able space to update the firmware.

Note

• The storage media in the USB card reader may not work.

• If the storage device has been partitioned, each section will be

treated as an independent device.

• If the USB mass storage device contains a lot of data, the AV

receiver may take a while to read it.

• Operation with all USB mass storage devices including the abil-

ity to power them is not guaranteed.

• Onkyo accepts no responsibility whatsoever for the loss or dam-

age to data stored on a USB mass storage device when that

device is used with the AV receiver. We recommend that you

back up your important music files beforehand.

• If you connect a USB hard disk drive to the USB port, we rec-

ommend that you use its AC adapter to power it.

• USB hubs and USB devices with hub functions are not sup-

ported. Do not connect your USB mass storage device via a USB

hub.

• USB memory devices with security functions are not supported.

• In no event shall Onkyo be liable to you or any third party for any

damages, whatsoever, arising from your use of or inability to use

the firmware, including but not limited to, loss of any equipment,

media or data, or other special, incidental or consequential dam-

ages, even if Onkyo has been advised of the possibility of such

damages.

The AV receiver allows you to update firmware using Net-

work connection on rear panel.

In this procedure, on-screen display may vary depending on

the model.

Note

• Make sure your AV receiver and TV are turned on and Ethernet

cable is connected to rear panel of the AV receiver.

• Never unplug or turn off the AV receiver during updating pro-

cess.

• Never plug or unplug an HDMI cable and Ethernet cable during

updating process.

• Never unplug the power cord during updating process.

• It will take about 60 minutes to update the firmware.

• The AV receiver will retain all your settings after update is fin-

ished.

Before you start

• Check “HDMI Control(RIHD)” setting (➔ 65). The

update may not be successful if this setting is on.

• Turn off the controller device connected via RS232C and

via Ethernet network.

• Turn off Powered Zone 2 and Powered Zone 3.

• Stop playback of content from Internet Radio, iPod,

USB or Servers, etc.

■ How to turn off RIHD

Update procedure

See the Onkyo web site for latest information.

Updating the Firmware via Network

In the Main menu select “Hardware Setup”.

Select “HDMI”.

Set “HDMI Control(RIHD)” to “Off”.

Press RECEIVER followed by SETUP on the

remote controller.

Main menu will be displayed on TV screen. Proce-

dures thereafter can also be performed on the AV

receiver by using its SETUP, arrow, and ENTER

buttons.

Go to “Hardware Setup” menu.

Go to “Firmware Update” menu.

Note that the Firmware Update option will be grayed

out about 50 seconds after AV receiver is turned on.

Please wait.

Select “Via NET” and press ENTER.

Select “Update” and press ENTER.

Updating will begin.

As the updating progresses, the TV screen may dis-

appear depending on the program updated. In this

case, you can see the update progress on the front

display of the AV receiver. The TV screen will reap-

pear when you finish the update and turn on the AV

receiver.

Message “Complete!” appears on the front dis-

play of the AV receiver, indicating that the update

has been completed.

Using ON/STANDBY on the front panel, turn off

and on the AV receiver.

Do not use ON or STANDBY on the remote control-

ler.

Congratulations!! Now you have the latest firmware

on your Onkyo AV receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 112

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info