492661
54
Zoom out
Zoom in
Vorherige Seite
1/168
Nächste Seite
Turning On & Basic Operations
En-54
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
You can adjust the brightness of the AV receiver’s display,
and switch the MASTER VOLUME indicator off and on
in conjunction.
You can display various information about the current
input source as follows.
The following information can be typically displayed.
*1
If the input signal is digital, the signal format is displayed.
Information is displayed for about three seconds, then the
previously displayed information reappears.
When you connect an u-capable Onkyo component, you
must configure the input display so that u can work
properly.
This setting can be done only from the front panel.
Using the Sleep Timer
1
Press RECEIVER once followed by SLEEP
repeatedly to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in 10
minute steps.
The SLEEP indicator lights on the AV receiver’s
display when the sleep timer has been set. The
specified sleep time appears for about 5 seconds, then
the previous display reappears.
Tip
If you need to cancel the sleep timer, press SLEEP
repeatedly until the SLEEP indicator goes off.
To check the time remaining until the AV receiver sleeps,
press SLEEP. Note that if you press again on SLEEP as
the time being displayed is 10 minutes or less, the sleep
timer will go off.
Setting the Display Brightness
1
Press RECEIVER once followed by DIMMER
repeatedly to cycle through the following patterns:
Normal brightness + indicator off.
Dim brightness + indicator off.
• Dimmer brightness + indicator off.
Normal brightness + indicator on (default).
Tip
(North American models) Alternatively, you can use
DIMMER on the AV receiver.
Displaying Source Information
1
Press RECEIVER once followed by DISPLAY
repeatedly to cycle through the available
information.
Tip
Alternatively, you can use DISPLAY on the AV receiver.
Sampling
frequency
Input source
Signal format
*1
Listening mode
Input signal
resolution
Output resolution
Changing the Input Display
1
Press TV/CD or GAME1.
TV/CD” or “GAME1” appears on the AV receiver’s
display.
2
Press and hold down the same button (about
3 seconds) to change the input display.
Repeat this step to select the desired input display.
Note
•“DOCK” can be selected for the “TV/CD”, “GAME1
input selector, but not at the same time.
Enter the appropriate remote control code before using the
remote controller for the first time ( page 96).
TV/CD DOCK
TAPE
TV/CD:
GAME1 DOCK GAME1:
54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo TX-NR3010 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo TX-NR3010

Onkyo TX-NR3010 Bedienungsanleitung - Deutsch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Holländisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Französisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Italienisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Spanisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Schwedisch - 168 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info