Bedienungsanleitung Onkyo TX-NR3010 (Seite 71 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Advanced Operations

En-71

The HDMI connection in your system is used to deliver

uncompressed digital audio and video information from

one device to the next. There is also additional information

about this digital content that can be delivered. Such

additional information is referred to as “metadata”.

Metadata Compatible mode should be used when there are

home theater components in your system, such as Blu-ray

disc players, set top boxes and displays that use this

additional metadata. For example, Metadata Compatible

mode should be set to ON when there are THX Media

Director™ Enabled devices in the system. This ensures

that this additional information can be received by your

Onkyo AVR and can be sent to other devices that are

connected in your home theater system, with no

interruption.

Digital Processing Crossover Network

Digital Crossover provides a separate routing system by

splitting the audio signal into separate frequency bands

optimized for each speaker driver. It provides a fine, three-

dimensional sound field that extend each driver’s

performance to the uppermost. With its built-in time

alignment function, this system also adjusts the sound

shifting that occurs when there is a physical offset between

sound drivers. At a digital processing level, it corrects this

offset by delaying the related audio signal.

Although this function is meant for speakers without

crossover network, it can also be used with bi-amped

speakers.

Tip

• This setting can be done while listening to an audio source.

• Press MODE/D (Blue) to switch from the current audio source to

test noises. Pressing MODE/D (Blue) again or the cursor buttons

will stop the test noises and switch back to the original audio

source.

Note

• This setting can only be made when “Speakers Type(Front A)”

or “Speakers Type(Front B)” is set to “Digital Crossover”

(➔ page 66).

■ Crossover

` “250Hz”, “320Hz”, “400Hz”, “500Hz, “630Hz”,

“800Hz”, “1000Hz”, “1250Hz”, “1600Hz”,

“2000Hz”, “2500Hz”, “3200Hz

”, “4000Hz”,

“5000Hz”

Output Band for Test

` High + Low

, High, Low:

Select the output for the audio signal.

Tip

• Pressing MODE/D (Blue) button plays band-limited test noises

which center on the specified frequency.

• We recommend choosing a crossover value that creates no

volume difference between “High” and “Low”.

Note

• Refer to your speaker manual when setting without the use of test

noises.

■ Overlap

` No

` Yes

With this setting, a frequency band near the specified

crossover frequency is output by both tweeters and

woofers. Based on the frequency selected for “Crossover”,

the cutoff frequency of the low-pass filter (LPF) will be set

to 1/3 octave up and that of the high-pass filter (HPF) to

1/3 octave down. Example: With a “Crossover” of

“3200Hz”, the cutoff frequency of the woofers’ LPF will

be “4000Hz”, and the tweeters’ HPF will be “2500Hz”.

Tip

• Sounds processed by Digital Processing Crossover Network are

played.

• You can switch from the current audio source to test noises by

pressing MODE/D (Blue).

• In the case of usage of the bi-amped speakers, if there is a

difference between the crossover frequency in the speakers’ built-

in network and the crossover frequency to be set on the AV

receiver, the frequency dip may be caused. Therefore, it is

recommended that this function should be set to “Yes”.

■ High Level, Low Level

` –6.0dB to 0.0dB

to +6.0dB in 0.5 dB steps.

With this setting, you can set the volume of tweeters and

woofers.

Tip

• Sounds processed by Digital Processing Crossover Network are

played.

• You can switch from the current audio source to test noises by

pressing MODE/D (Blue).

THX Loudness Plus

THX Loudness Plus is a new volume control technology

featured in THX Ultra2 Plus™ and THX Select2 Plus™

Certified receivers. With THX Loudness Plus, home

theater audiences can now experience the rich details in a

surround mix at any volume level. A consequence of

turning the volume below Reference Level is that certain

sound elements can be lost or perceived differently by

the listener. THX Loudness Plus compensates for the

tonal and spatial shifts that occur when the volume is

reduced by intelligently adjusting ambient surround

channel levels and frequency response. This enables

users experience the true impact of soundtracks

regardless of the volume setting. THX Loudness Plus is

automatically applied when listening in any THX

listening mode. The new THX Cinema, THX Music, and

THX Games modes are tailored to apply the proper THX

Loudness Plus settings for each type of content.

Cutoff frequencies of the woofers’ low-pass filter (LPF)

and the tweeters’ high-pass filter (HPF) are set according

to the frequency specified for “Crossover”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info