Bedienungsanleitung Onkyo TX-NR3010 (Seite 99 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Controlling Other Components

En-99

The AV receiver’s remote controller can learn the

commands of other remote controllers. By transmitting, for

example, the Play command from your CD player’s remote

controller, the supplied remote controller can learn it and

then reproduce the exact same command when its 1 is

pressed in CD remote mode.

This is useful when some buttons don’t work as expected

though you entered the appropriate remote control code

(➔ page 95).

Note

• The following buttons cannot learn new commands:

8RECEIVER, ALL OFF, MY MOVIE, MY TV, MY MUSIC,

REMOTE MODE, MODE.

• The remote controller can learn approximately 70 to 90

commands, although this will be less if commands that use a lot

of memory are learned.

• Remote controller buttons such as Play, Stop, and Pause are

preprogrammed with commands for controlling Onkyo CD

players, cassette decks, and DVD players. However, they can

learn new commands, and you can restore the preprogrammed

commands at any time by resetting the remote controller

(➔ page 96).

• To overwrite a previously acquired command, repeat this

procedure.

• Depending on the remote controller used, some buttons may not

respond as expected, or the learning process itself may not be

possible.

• Only commands from infrared remote controllers can be

acquired.

• When the remote controller runs out of batteries, all commands

acquired will be lost and will have to be learned all over again.

Therefore, do not discard your other remote controllers.

■ Deleting Acquired Commands

1. While holding down the REMOTE MODE button for

the mode from which you want to delete a command,

press and hold down 8TV until the REMOTE MODE

button lights (about 3 seconds).

2. Press the REMOTE MODE button or the button from

which you want to delete the command.

The REMOTE MODE button flashes twice.

When you press the REMOTE MODE button, all

commands learned in that mode will be deleted.

Learning Commands

While holding down the REMOTE MODE button

for the mode in which you want to use the

command, press and hold down 8RECEIVER

until the REMOTE MODE button lights (about 3

seconds).

On the supplied remote controller, press the

button to which you want to assign the new

command.

Point the remote controllers at each other, within

about 4 inches (10 cm) apart, and then press and

hold the button whose command you want to

acquire until the REMOTE MODE button flashes.

8RECEIVER

REMOTE

MODE

If the command is learned successfully, the

REMOTE MODE button flashes twice.

To learn more commands, repeat steps 2 and 3.

Press any REMOTE MODE button when you’ve

finished. The REMOTE MODE button flashes

twice.

VOLUME

ING

POWER

SLEEP

DIMM

SUR

MODE

VIDEO-1

VIDEO-2

TAP E

DVD

C D

DVD

NER

TUNER

PHONO

INPUT SELECT

DISC

CH SEL

PRESET

TEST

TON

MULTI-CH

INPUT

GROUP

Within about

4 inches (10 cm)

Supplied remote

controller

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info