Bedienungsanleitung Onkyo TX-NR3030 (Seite 8 von 24) (Englisch)

553768

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Step 2:

Setting Up

Important: When the unit is turned on for the first time, the

setup wizard of the section 2 will automatically be launched.

If you use the setup wizard to make the initial setup,

connect a TV to the HDMI OUT MAIN or SUB jack of the

unit via HDMI connection.

Turning the power on

Connect the power cord to the outlet. Press

ON/

STANDBY on the main unit or

RECEIVER on the remote

controller to turn the unit on or to standby mode.

Initial Setup

Language Select

English

Deutsch

Français

Español

Italiano

Nederlands

Svenska

HOME Exit

¼

This unit includes a removable power cord. Connect the power

cord to AC INLET of the unit and then connect to the outlet. Always

disconnect the outlet side first when disconnecting the power cord.

When the unit is turned on, a large instantaneous current may

flow affecting functionality of the computer and other devices. It is

recommended to use a separate outlet from that for the computer or

such other sensitive devices.

Firmware update notification: If the unit is connected

via LAN and there is firmware update available, the

"Firmware Update Available" message will appear. To

execute updating, select "Update Now" with the cursor

buttons of the remote controller and press ENTER. When

"Completed!" appears, press

ON/STANDBY on the main

unit to turn the unit into standby mode. Then updating will

be completed.

r The unit automatically turns itself into standby mode 3

minutes after "Completed!" appears on the display. In this

case also, updating will be completed.

Making the Initial Setup with the Setup Wizard

Read before starting the procedure: Set up by

answering the guidance displayed on the TV screen.

Select the item with the cursor buttons of the remote

controller and press ENTER to confirm your selection.

To return to the previous screen, press RETURN.

r If you terminate the procedure on the way or

change the setting made in the initial setup and

want to call up the setup wizard again, press

RECEIVER and then HOME on the remote

controller, select "Setup" - "7.Hardware Setup" -

"Initial Setup", and press ENTER.

Select the language first. In the next screen, the summary

of the setup wizard as below will be displayed. Select "Yes"

in this screen and press ENTER on the remote controller.

Welcome to initial setup. Have you connected all the speakers and devices?

Before starting, please connect speakers and sources.

Now, would you like to start initial setup?

1st Step : AccuEQ Room Calibration

2nd Step : Source Connection

3rd Step : Remote Mode Setup

4th Step : Network Connection

Yes

Initial Setup

ExitHOME

The setup wizard proceeds in the four steps as below.



1st Step : AccuEQ Room Calibration



2nd Step : Source Connection



3rd Step : Remote Mode Setup



4th Step : Network Connection



1st Step : AccuEQ Room Calibration

The test tone coming from each speaker will be measured to

enable setting of the number of speakers, volume level, each

speaker's optimum crossover frequencies, and distance from

the primary listening position, and also enable correction of

distortion caused by the room acoustic environment.

r You cannot return to the previous screen during speaker

setup, even if you press RETURN.

r You cannot setup the wide speaker setting in the setup

wizard. For details on setting up the wide speakers, see

the Advanced Manual.

Initial Setup

AccuEQ Room Calibration

This step you can automatically calibrate

your room to get correct surround sound.

Would you like to cailbrate your room now

or later?

Do it Now

Do it Later

ExitHOME

Place the speaker setup microphone.

When the start screen above is displayed, before

starting the procedure, place the supplied speaker setup

microphone at the measurement position



by referring

to the figure below.

Listening area Measurement position

with microphone

¼

Correct measurement will not be possible if the microphone is held

by hand. Measurement is not possible if headphones are being used.

¼

The subwoofer sound may not be detected since it is extremely low

frequencies. Raise the subwoofer volume to around the half of its

maximum volume and make its frequency to the maximum level.

¼

A loud test tone will be heard during measurement. Measurement

may be interrupted if there is ambient noise or radio frequency

interference. Close the window and turn off the home appliance and

fluorescent light.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3030 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3030

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info