Bedienungsanleitung Onkyo TX-NR414 (Seite 55 von 128) (Englisch)

492644

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Controlling Other Components

En-55

Controlling Other

Components

You can use the AV receiver’s remote controller to control

your other AV components. This section explains how to

enter the remote control code for a component that you

want to control: DVD, TV, CD, etc.

The following REMOTE MODE buttons are

preprogrammed with remote control codes for controlling

the components listed. You do not need to enter a remote

control code to control these components.

For details on controlling these components, see the

indicated pages.

You’ll need to enter a code for each component that you

want to control.

Note

• Though the provided remote control codes are correct at the time

of release, they are subject to change.

You can change the configuration of colored buttons, with

which REMOTE MODE buttons are preset.

Tip

•To reset the REMOTE MODE buttons to their default settings,

see “Resetting the REMOTE MODE Buttons” (➔ page 56).

Note

• If any other button than the colored buttons is pressed, the

operation will be cancelled.

• This operation cannot be done while the AV receiver is in

Receiver mode or when ZONE 2 is active.

Preprogrammed Remote Control

Codes

BD/DVD Onkyo Blu-ray Disc player (➔ page 57)

TV/CD Onkyo CD player (➔ page 56)

Entering Remote Control Codes

Look up the appropriate remote control code in the

separate Remote Control Codes list.

The codes are organized by category (e.g., DVD

player, TV, etc.).

While holding down the REMOTE MODE button to

which you want to assign a code, press and hold

down DISPLAY (about 3 seconds).

The remote indicator lights.

Note

• Remote control codes cannot be entered for RECEIVER

and the multi zone button.

• Only TV remote control codes can be entered for TV.

• Except for RECEIVER, TV, and the multi zone button,

remote control codes from any category can be assigned for

the REMOTE MODE buttons. However, these buttons also

work as input selector buttons (➔ page 20), so choose a

REMOTE MODE button that corresponds with the input to

which you connect your component. For example, if you

connect your CD player to the CD input, choose TV/CD

when entering its remote control code.

Within 30 seconds, use the number buttons to enter

the 5-digit remote control code.

The remote indicator flashes twice.

If the remote control code is not entered successfully,

the remote indicator will flash once slowly.

Remapping Colored Buttons

While holding down the REMOTE MODE button

that you want to program, press and hold down A

(Red) until the remote indicator lights (about 3

seconds).

You can only change colored buttons for components

whose codes belong to categories of the Remote

Control Codes list (BD/DVD player, TV, cable set-top

box, etc).

Within 30 seconds, press the colored buttons in the

order that you want to reassign them.

The button presses are assigned to each button from

left to right. The remote indicator flashes twice,

indicating that the sequence has been successfully

assigned. If the sequence is not successfully assigned,

the remote indicator will flash once slowly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR414 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR414

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info