Bedienungsanleitung Onkyo TX-NR5007 (Seite 154 von 164) (Englisch)

553765

154

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

154

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue

yourself, contact your Onkyo dealer.

Can’t turn on the AV receiver

• Make sure that the power cord is properly plugged into

the wall outlet.

• Unplug the power cord from the wall outlet, wait five

seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet immedi-

ately. Disconnect all speaker cables and input sources,

and leave the AV receiver with its power cord discon-

nected for 1 hour. After that, reconnect the power cord

and set the volume to maximum. If the AV receiver

stays on, set the volume to minimum, disconnect the

power cord, and reconnect your speakers and input

sources. If the AV receiver turns off when you set the

volume to maximum, disconnect the power cord, and

contact your Onkyo dealer.

There’s no sound, or it’s very quiet

• Make sure that the digital input source is selected

properly (page 56).

• Make sure that all audio connecting plugs are pushed

in all the way (page 29).

• Make sure that the inputs and outputs of all compo-

nents are connected properly (pages 31 to 46).

• Make sure that the polarity of the speaker cables is

correct, and that the bare wires are in contact with the

metal part of each speaker terminal (page 20).

• Make sure that the input source is properly selected

(page 67).

• Make sure that the speaker cables are not shorting.

• Check the volume. It can be set to

−Q dB, −81.5 dB

through +18.0 dB (page 67). The AV receiver is

designed for home theater enjoyment. It has a wide

volume range, allowing precise adjustment.

• If the MUTING indicator is flashing on the display,

press the remote controller’s [MUTING] button to

unmute the AV receiver (page 69).

• While a pair of headphones is connected to the

PHONES jack, no sound is output by the speakers

(page 70).

• If there’s no sound from a DVD player connected to an

HDMI IN, check the DVD player’s output settings,

and be sure to select a supported audio format.

• Check the digital audio output setting on the con-

nected device. On some game consoles, such as those

that support DVD, the default setting is off.

• With some DVD-Video discs, you need to select an

audio output format from a menu.

• If your turntable uses an MC cartridge, you must con-

nect an MC head amp, or an MC transformer.

• Make sure that none of the connecting cables are bent,

twisted, or damaged.

• Not all listening modes use all speakers (page 89).

• Specify the speaker distances (page 97) and adjust the

individual speaker levels (page 97).

• Make sure that the speaker setup microphone is not

still connected.

• The input signal format is set to PCM or DTS. Set it to

Auto (page 116).

Only the front speakers produce sound

• When the DTS Surround Sensation, Stereo or Mono

listening mode is selected, only the front speakers and

subwoofer produce sound.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“Left / Right” (page 100).

• Check the Speaker Configuration (page 95).

Only the center speaker produces sound

• If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game listen-

ing mode with a mono source, such as an AM radio

station or mono TV program, the sound is concen-

trated in the center speaker.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“Center” (page 100).

• Make sure the speakers are configured correctly

(page 95).

Power

Audio

If you can’t resolve the issue yourself, try resetting

the AV receiver before contacting your Onkyo

dealer.

To reset the AV receiver to its factory defaults,

turn it on and, while holding down the [VCR/DVR]

button, press the [ON/STANDBY] button. “Clear”

will appear on the display and the AV receiver will

enter Standby mode.

Note that resetting the AV receiver will delete your

radio presets and custom settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR5007 Seite 154

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR5007

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info