Bedienungsanleitung Onkyo TX-NR5008 (Seite 113 von 116) (Englisch)

553766

113

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

113

Troubleshooting

Case1:

If “No Update” is displayed on the front display of the AV

receiver, the firmware has already been updated. You do

not need to do anything further.

Case2:

If an error occurs, “Error!! *-** No media” is displayed

on the front display of the AV receiver. (Alpha-numeric

characters on the front display are denoted by asterisks.)

See the following table and take appropriate action.

■ Errors during update via Network

Case3:

If you do not have a wired connection to the network,

please contact Onkyo Support (➔ 114).

Case4:

If an error occurs during updating process, disconnect then

reconnect the AC power cord and try again.

Case5:

If an error has occurred due to wrong selection of input

sources, turn off and on the AV receiver. Then retry the

update.

The AV receiver allows you to update firmware using a

USB storage device.

In this procedure, on-screen display may vary depending on

the model.

Note

• Never unplug or turn off the AV receiver during updating pro-

cess.

• Never plug or unplug an HDMI cable and a USB device during

updating process.

• Never unplug the USB mass storage device and the power cord

during updating process.

• It will take about 60 minutes to update the firmware.

• The AV receiver will retain all your settings after update is fin-

ished.

Before you start

•Check “HDMI Control(RIHD)” setting (➔ 65). The

update may not be successful if this setting is on.

• Turn off the controller device connected via RS232C and

via Ethernet network.

• Turn off Powered Zone 2 and Powered Zone 3.

• Stop playback of content from Internet Radio, iPod,

USB or Servers, etc.

■ How to turn off RIHD

Update procedure

Error Code Description

-10,

-20

Ethernet cable is not detected. Connect the

cable properly.

-11,

-13,

-21,

-28

Internet connection error.

Check the following items:

• Make sure IP address, subnet mask, gateway

address, and DNS server are configured prop-

erly.

• Make sure the router is turned on.

• Make sure the AV receiver and the router are

connected with Ethernet cable.

• Make sure the setup configuration of the

router is set properly. See the instruction

manual of the router.

• If your network allows only one client con-

nection and there is any other device already

connected, the AV receiver cannot access the

network. Consult your Internet Service Pro-

vider (ISP).

• If your modem does not function as a router,

you will need a router. Depending on your

network, you may need to configure the

proxy server if needed. See the document

provided by your ISP. If you still cannot

access the Internet, DNS or proxy server may

be temporarily down. Contact your ISP.

Others Retry the update procedure from the begin-

ning. If the error persists, please contact

Onkyo Support (➔ 114) and provide the error

code.

Updating the Firmware via USB

In the Main menu select “Hardware Setup”.

Select “HDMI”.

Set “HDMI Control(RIHD)” to “Off”.

Connect a USB storage device to your PC. If

there is any data in the USB storage, remove it.

Download the firmware file from the Onkyo

web site. The file name is as follows:

ONKAVR0001_*******.zip

Unzip the downloaded file. The following three

files are created:

ONKAVR0001_*******.of1

ONKAVR0001_*******.of2

ONKAVR0001_*******.of3

Copy the extracted files to the USB storage

device. Be careful not to copy the zip file.

Remove the USB storage device from your PC

and connect it to the USB port on the AV

receiver.

When the AV receiver has two USB ports, you can

use either one.

Make sure the AV receiver and TV are turned

on.

If the AV receiver is in standby mode, press ON/

STANDBY on the AV receiver to light up the

front display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR5008 Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR5008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info