Bedienungsanleitung Onkyo TX-NR579 (Seite 74 von 84) (Englisch)

462088

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Firmware Update

To update the firmware of the AV receiver, you can

choose from the following two methods: update via

network, or update via USB storage. Choose the one that

best suits your environment. Before proceeding with the

update, please read the corresponding explanations

carefully.

■ Update via network

You need a wired Internet connection to update the

firmware.

■ Update via USB storage (➔ page 75)

Please prepare a USB storage device such as a USB

flash memory stick. You need at least 32 MB of

available space to update the firmware.

Note

• Check the network connection before updating.

• Do not touch the any cable or device connected to the AV

receiver during the update process.

• Do not attempt to access the AV receiver from your PC while it

is being updated.

• Do not shutdown the power of the AV receiver while it is being

updated.

• The storage media in the USB card reader may not work.

• If the USB device is partitioned, each section will be treated as

an independent device.

• If the USB device contains a lot of data, the AV receiver may

take a while to read it.

• Operation is not guaranteed for all USB devices, which includes

the ability to power them.

• Onkyo takes no responsibility whatsoever for the loss or damage

of data resulting from the use of a USB device with the AV

receiver. Onkyo recommends that you back up your important

music files beforehand.

• If you connect a USB hard disk drive to the USB port, Onkyo

recommends that you use its AC adapter to power it.

• USB hubs and USB devices with hub functions are not

supported. Do not connect your USB device via a USB hub.

• USB devices with security functions are not supported.

The AV receiver allows you to update the firmware using

network connection on the rear panel.

Note

• Make sure your AV receiver and TV are turned on and an

Ethernet cable is connected to the rear panel of the AV receiver.

• Never unplug or turn off the AV receiver while it is being

updated.

• Never plug or unplug an HDMI or Ethernet cable during the

update process.

• Do not attempt to access the AV receiver from your PC while it

is being updated.

• Never unplug the power cord during the update process.

• It takes maximum 60 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is

finished.

Before you start

• Set the “HDMI Control (RIHD)” setting to “Off”

(➔ page 52).

• Turn off the controller device connected via Ethernet

cable.

• Turn off Zone 2.

• Stop playback of contents from Internet Radio,

iPod/iPhone, USB or servers, etc.

Update procedure

Limitation of liability

The program and accompanying online documentation

are furnished to you for use at your own risk. Onkyo

will not be liable and you will have no remedy for

damages for any claim of any kind whatsoever

concerning your use of the program or the

accompanying online documentation, regardless of

legal theory, and whether arising in tort or contract. In

no event will Onkyo be liable to you or any third party

for any special, indirect, incidental, or consequential

damages of any kind, including, but not limited to,

compensation, reimbursement or damages on account of

the loss of present or prospective profits, loss of data, or

for any other reason whatsoever.

See the Onkyo web site for latest information.

Updating the Firmware via Network

Press RECEIVER followed by SETUP on the

remote controller.

The Setup menu will be displayed on the TV screen.

The procedures thereafter can also be performed on

the AV receiver by using its SETUP, arrow and

ENTER buttons.

Select “Hardware Setup” and press ENTER.

Select “Firmware Update” and press ENTER.

Note that the “Firmware Update” option will be

grayed out for a short while after the AV receiver is

turned on. Please wait until it becomes operable.

Select “Via NET” and press ENTER.

Select “Update” and press ENTER.

The update process will begin.

During the update process, the on-screen display

may disappear depending on the updated program.

When this occurs, you can still view the update

progress on the front display of the AV receiver. The

on-screen display will reappear after the update is

complete, and upon turning the AV receiver off and

on again.

The message “Completed!” appears on the front

display of the AV receiver, indicating that the

update has been completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR579 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR579

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info