Bedienungsanleitung Onkyo TX-NR676E (Seite 23 von 91) (Englisch)

686240

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

The speakers emit the test tone at high volume during

measurement, so be careful of your surroundings. Keep the

room as quiet as possible during measurement.

0 If you have connected a subwoofer, check the power and

volume of the subwoofer. Set the subwoofer volume to

more than halfway.

0 If the power of this unit suddenly turns off, the wires in

the speaker cables may have touch the rear panel or

other wires and tripped the protection circuit. Twist the

wires again properly and make sure they do not stick out

of the speaker terminals when connecting.

1. Place the supplied speaker setup microphone in the

listening position, and connect to the SETUP MIC jack on

the main unit.

When putting the speaker setup microphone on a tripod,

refer to the illustration when putting it in place.

2. Select the connected speaker configuration.

The image on the screen changes as you choose the

number of channels in "Speaker Channels", so refer to it

when performing the settings.

3. Test tones are emitted by the speakers, and firstly the

unit detects the speakers connected and the noise in the

environment.

4. After the results of the above measurements are

displayed, select "Next", press ENTER on the remote

controller, and the test tones are emitted again, and the

unit automatically makes settings such as the optimum

volume level and the crossover frequency.

5. When the measurement is completed, the measurement

result is displayed. Press the cursors  /  on the

remote controller to check the settings. Press ENTER

when "Save" is selected to save the settings.

6. Select whether to enable or disable the equalizer

function that corrects for distortion caused by the

acoustic environment of the room.

If this is to be enabled, then normally you should select

"On (All Channels)", and to disable just the front

speakers you should select "On (Except Front Left /

Right)".

7. Disconnect the speaker setup microphone.

∫ 2. Source Connection

Check that each input source is connected correctly. Follow

the guidance, select the input you want to confirm, start

play of the selected player, and confirm that the images

appear on the TV and that sound is played.

∫ 3. Network Connection

Set up Wi-Fi connection with an access point such as a

wireless LAN router. There are the following two methods of

connecting by Wi-Fi:

"Scan Networks": Search for an access point from this

unit. Find out the SSID of the access point beforehand.

"Use iOS Device (iOS7 or later)": Share the iOS device's

Wi-Fi settings with this unit.

If you select "Scan Networks", there are a further two

choices of connection method. Check the following.

"Enter Password": Enter the password (or key) of the

access point to connect.

"Push Button": If the access point has an automatic

connection button, you can connect without entering a

password.

0 If the SSID of the access point is not displayed, then in

the screen listing the SSIDs, select "Other..." with the 

cursor on the remote controller and press ENTER, then

follow the onscreen instructions.

Keyboard Input

To switch between upper and lower case, select "A/a" on

the screen and press ENTER. To select whether to mask

the password with "" or display it in plain text, press

MEMORY on the remote controller. Press CLEAR to delete

all the input characters.

0 A confirmation screen asking you to agree to the privacy

policy is displayed during network setting. Select

"Accept" and press ENTER to indicate agreement.

∫ 4. Multi Zone Setup

When you want to enjoy audio in a room other than the

main room, set the audio output method for the separate

room (ZONE 2). If you have connected speakers in a

separate room with speaker cable, select "Using AV

Receiver". If you have connected a pre-main amplifier in a

separate room with an analog audio cable, select "with

External Premain Amplifier".

∫ 5. Audio Return Channel

If you have connected a TV that supports ARC, select

"Yes". This unit's ARC setting turns on and you can listen to

the TV's audio through this unit.

SETUP MIC

AccuEQ Room Calibration

Speaker Channels

Subwoofer

Height Speaker

Zone Speaker

Bi-Amp

Select how many speakers you have.

7.1 ch

< >

Yes

---

> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual

Troubleshooting | Supplementary Information, etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR676E Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR676E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info