Bedienungsanleitung Onkyo TX-NR676E (Seite 46 von 91) (Englisch)

686240

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

> Specifications > Advanced Setup > Listening Modes > Network Functions

Troubleshooting Supplementary Information, etc.|

> Basic Manual

■ 4. Level Calibration

Setting Item Default Value Setting Details

Front Left 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Center 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Front Right 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Height Left 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

Height Right 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

Surround Right 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Setting Item Default Value Setting Details

Surr Back Right 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

Surr Back Left 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

Surround Left 0 dB Select a value between "−12 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Subwoofer 0 dB Select a value between "−15 dB" and "＋12 dB"

(in 1 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

■ 5. Dolby Enabled Speaker

Setting Item Default Value Setting Details

Dolby Enabled

Speaker to

Ceiling

6.0 ft/1.80 m Set the distance between the Dolby Enabled

Speaker and the ceiling. Select between "0.1

ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).

•

The unit of distance (ft/m) shown is the unit

selected for use in "Distance".

AccuReflex Off You can enhance the reflection effect of Dolby

Enabled Speakers from the ceiling.

"Off": When this function is not to be used

"On": When this function is to be used

•

This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR676E Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR676E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info